Tools needed to remove the door card
To remove the door trim on a Corolla or Auris you will need:
- two screwdrivers, one flat and the other Phillips;
- and the key to “10”.
Also, do not forget that since you will need to disconnect several electrical connectors, in order not to short anything, God forbid, you should disconnect the battery terminal.
In order to pull off the door card and not damage the surface of the door or the clips on which the trim is fixed, it is advisable to use a special plastic device or use a wide flat screwdriver wrapped in fabric.
The entire subsequent procedure for removing the Toyota Corolla 150 front door card can be clearly seen in these illustrations:
Auto giants are increasingly having to enter into negotiations with labor collectives over concessions in personnel costs, which usually make up the bulk of a manufacturer’s costs.
See all photo news >>
The next victim of falling demand on world markets is the BMW concern, which is looking for ways to optimize its budget. The other day, the company's management announced that it had reached an agreement with trade unions to reduce costs, which allows them to avoid radical measures against labor collectives.
The agreement includes cuts to bonuses based on company profits, as well as changes to Christmas pay and other bonuses for some workers. The measures will be introduced from 2021. It is reported that compared to last year, bonus payments will be almost 20 percent lower.
BMW aims to save more than 12 billion euros by 2022, which explains the decision to enter into negotiations with union representatives and leading suppliers.
The result was a solution based on solidarity, said company CEO Oliver Zipse. This will avoid the drastic measures that other automakers are currently taking to cut their costs, he added. By this he means mass layoffs, the closure of individual sites or the cessation of active work in some regions. Such actions have already been observed in the last year by such companies as Ford, Daimler, Audi and other large companies.
Let us remind you that leading representatives of the German auto industry have to intensify efforts to reduce costs in order to find funds for investments that are necessary for the deployment of large-scale production of electric vehicles and the development of new technologies. Only this can make it possible to maintain competitiveness in the long term, company management admits.
And the European automotive industry is increasingly being pushed to switch to environmentally friendly transport by rules for reducing emissions in the EU, which will only become stricter. And they will be almost impossible to achieve without a significant increase in the production and sales of electric vehicles, which until now have had limited demand from consumers. Trade wars and declining demand in key markets such as China have made the transition to new technologies even more challenging.
See all photo news >>
Buy used Toyota Corolla spare parts – how to make a purchase?
You have a great opportunity to make sure that in a matter of days the component that your car is so lacking is in your hands. The assortment of the Razbor66 online store will amaze even the most demanding customer.
Buying used Toyota Corolla spare parts couldn't be easier! Go to the website, select a part in a few clicks and make a payment. That's all that is required of you. Our specialists will prepare and send the goods as soon as possible. Already received it? Then be sure to install the part on your car and check its functionality, because you have time to demand a refund or replacement of a component that for some reason did not suit you.
Toyota Corolla BEAUTY › Logbook › First experience of covering door cards
I welcome everyone who may be interested in this process.
Over the weekend I devoted myself entirely to the car. I decided to start with the door cards. I unscrewed 2 bolts (the first behind the door handle and the second in the niche of the pocket under the plug)
Photo from the instructions for the car on how to remove the door trim Then I went home and again began dismantling while Vasily (the parrot) was singing
I cut off the fastening clips and cut out an approximate piece from eco-leather with a margin of 2-3 cm. 88glue, I still couldn’t find it... Something was selling out quickly (the seller said that there was some kind of excitement about it...) I tried it in a moment (it also says 88 there) nothing... it gets absorbed somehow holds...nothing at all! I decided to glue it with proven glue (liquid nails)
Do not apply too much glue, it is almost not absorbed! Coat the surface with bends completely. If there is a lot of glue it will come out through the perforation! It will be ugly and then you will have to clean the surface... very inconvenient...
So that’s how it happened. Then I sealed the fastening points with a glue gun.
First, a little inside, then everything with a little mound
Assembled When I inserted and soldered, I pulled it up by the edges of the skin so that there were no folds. In general, it turned out well! I liked it and there is nothing complicated! This is what it looks like in the car There is a small little joint, but we can fix it) it came off a little bit... And lastly, I sewed the cover for the gear knob myself✌ Now I’m learning how to tighten the knob cap and steering wheel Thank you all and good luck! I hope my advice will help someone ☝
Toyota Corolla front door
- disconnect the battery terminals to avoid short circuit;
- dismantle the plastic casing. The algorithm of actions is described above;
- remove the protective polyethylene placed on the sealant. As well as electrical wiring, contact boards, metal glass guides;
- dismantle the plastic trims on the threshold;
- This is not enough to remove the door. We unscrew the trim at the place where the windshield wipers are attached: two bolts and three plastic clips;
- dismantle the wheel, remove the fender liner. In a Toyota Corolla 150, another plastic protection is installed under the fender liner; it also needs to be removed. In the cavity of the wheel arch, unscrew one bolt - the retainer;
- We proceed to dismantling the left / right part of the front bumper. This is necessary to remove the wing. The process is not complicated, just three bolts;
- After removing the wing and disconnecting the bumper, unscrew the door from the standard hinges. Otherwise, the design will not allow it.
Carefully unscrew three bolts on each hinge and remove. We carry out preventive maintenance and begin preparations for the installation of a new body element.
Be sure to cover the perimeter of the door with masking tape to avoid damaging the paintwork. We start the block with electrical wires, fix the upper and lower loops, but do not clamp them. We set the gaps to the “level”, after which we finally tighten the bolts. We fix the guides, insert the double-glazed window, connect the blocks with wires. Finally, screw the door handle into place.
How to Remove Door Trim on Toyota Corolla 150
Body parts are something that gets damaged quite often, especially doors and fenders. But knowing how to disassemble, for example, the rear right door, may be required not only when replacing it, but also when carrying out other work: replacing wiring, repairing power windows, installing speakers for an audio system.
The rear left door of the Toyota Corolla 150 can be removed quite easily, just open the bolts that hold it, but this procedure is not required very often. A more popular question among owners is how to disassemble a door on a Toyota Corolla 150.
This is a necessary skill if you decide to install additional sound insulation on a car, you will need to replace or repair power windows, tamper with the wiring, or install speakers for listening to music.
Removing the rear door trim is not the most difficult process, so it can be completed entirely in a garage. To carry out the work, you will need to arm yourself with a 10-mm wrench, Phillips and flat-head screwdrivers. When working, you will need to pay attention to the electrical connectors. They will need to be disconnected and then not forgotten to be put back in place.
Tip: to protect yourself from short circuits when carrying out work, remove the positive terminal from the battery.
The trim is attached to the door using plastic clips. They are easy to destroy, so you need to remove them with special plastic equipment. Then the material remains intact, and you won’t break the clips themselves. If you don’t have a tool, a large flat-head screwdriver will do, but you need to wrap it in fabric first to eliminate the risk of tearing the casing with its tip.
Removal and adjustment
On a Toyota Corolla 2008, removing the doors, as on a car in the 120 and 150 body of any other year, will not cause any difficulties. Removing them is simple: after disassembling the casing, you need to disconnect the wiring. Then you will need to unscrew the bolts that attach the door hinges to the body. If the bolts do not come off, you can use WD-40 or try to heat them; as a last resort, the bolt can be drilled out and replaced with a new one. If you know how to use welding, you can weld a small piece of metal on top of the bolt, and on it a nut of 12 or more, try to unscrew such a bolt using a wrench.
The product is installed in the reverse order. Door adjustment on a Toyota Corolla is required after each removal, as well as during operation if you notice that they begin to close poorly.
You can check whether the adjustment has been carried out correctly as follows: open the door and lift it so that the body remains stationary. If it rises more than 1.6 cm, the hinges need to be replaced.
Please note that if you removed, for example, the rear right door, after installing it back the gaps should be the same everywhere, the structure should not warp.
The surface should not protrude beyond the level of other body parts.
Adjustment occurs using bolts connecting the hinges. After loosening them, place the door in the desired position, then tighten the bolts sufficiently tightly.
How to Remove a Door Trim on a Toyota Corolla 100
Door to Toyota Corolla
Body parts are often damaged, especially doors and wings. However, knowing how, for example, the rear right door is disassembled, it may be necessary not so much to replace it as to perform other work: replacing electrical wiring, repairing windows, installing speakers for an audio system.
How to remove the casing?
Rear left door of Toyota Corolla 150 is easy to remove
, simply open the bolts that hold it in place, but this procedure is not very common. A more popular question among owners is how to disassemble the doors on a Toyota Corolla 150.
This is a necessary skill if you decide to install additional sound insulation on your car, you will need to change what it is called, repair windows, interfere with electrical wiring or install speakers to listen to music.
Removing the rear door
- not the most difficult process, so this can be done in a garage. You will need to equip yourself with 10-key, Phillips and flat-head screwdrivers. You will need to pay attention to electrical outlets when working. They will need to be disabled, then be sure to place them in the zone.
Advice. To protect yourself from short circuits during operation, remove the positive terminal from the battery.
The door trim is secured with plastic clips. They are easy to destroy, so they need to be removed using special plastic equipment. This way the fabric remains intact and you won't break the clips yourself. If you don't have the tool, a large flat head screwdriver will do, unfortunately you will need to wrap it in cloth beforehand to avoid the risk of tearing it.
How do I get started?
You may also like
There is no need to remove the door itself if you are interested in trim. First of all, you will need to remove
its card: if there is an electric window installed on its surface (usually the right front door or front left door of Toyota), you first need to tear off the plastic panel, the controls are occupied. Carefully unscrew the bolts of the device, remove the remaining wires that lead to our customer's buttons.
Removing door trim for Toyota Karina, Corolla, etc.
Disassemble the front door
for
Toyota Carina, Toyota Corolla
and other similar models. Take off.
How to remove door trim. Toyota Corolla X (E140, E150) restyling.
All about body repair! All educational materials for cars. Own business, tuning, free lessons. A.
Before removing the door on a Toyota Corolla, it is recommended to watch a video of similar work: it will help you better navigate the world and understand how to act. Carefully inspect the door handle: it is attached to the plastic with a bolt that needs to be unscrewed.
When our client remains screwed in, it is possible to remove
plastic trim from the door handle protrusions. To do this, you need to push them with a narrow object. You may need a utility knife, also called a flat-head screwdriver, but be careful: the soft plastic may get scratched or otherwise damaged. Below the spacers there will be several bolts that secure the handles.
Toyota Corolla rear door
We open the door and dismantle the plastic casing according to the algorithm described above. Remove the decorative trim from the threshold and disconnect the electrical wiring. We unscrew each of the hinges one by one and remove the body element.
We carry out preventive maintenance, install the new door in its original place, having previously covered the perimeter with masking tape to avoid accidental damage to the paintwork. We assemble the structure in reverse order. The gaps will be uniform provided there is no deformation of metal surfaces, impacts, accidents, or collisions.
