Replacing license plate light bulb for Toyota Corolla 150 body

Is it possible to replace it yourself?

You can change the light bulbs in the license plate lights yourself. The best lighting option is an LED bulb, which is not afraid of moisture and small mechanical shocks. The manufacturer installs two lighting lamps. Some amateurs are not satisfied with them because they produce weak light. They are upgrading it with LED strips. License plate illumination is required. The choice of lighting color for most Russian citizens is limited to white and yellow.

What is the low beam lamp for Toyota Corolla 2007 - we cover it point by point

Some Toyota Corolla car owners complain that the factory-assembled low beam of the latest car model does not suit them; the minions shine dimly, not providing the necessary visibility.
This problem is easily solved. The lighting in the Corolla headlights can be easily changed. To do this, you just need to change the light bulbs, in our case the low beam. Burnt out minions also need replacing. This process is simple and takes from 2 to 5 minutes if you know how to do it. The only problem is that the lighting fixtures are located in hard-to-reach places. But this can also be solved.

Requirements for rear license plate illumination

According to traffic rules, on the territory of the Russian Federation, the state registration license plate of a car must be clearly readable at a distance of 20 meters, both in daylight and in the dark. Room lighting is required. A fine will be imposed for the absence of a lighting lamp, its breakdown, or contamination. This is an external lighting device and the general requirements for lighting devices and reflectors apply to it. The driver will be fined or warned for the complete absence of license plate illumination if at least one lamp does not work, even if all letters and numbers are fully visible.

Fielder number illumination

Also nothing complicated, but you will need to remove the trim on the rear wall of the trunk. To do this, you need to disconnect the fastening clips - the clips are fragile and break easily, so it is wise to stock up on them in the store.

After removing the casing, you can pull out the non-working light bulb and disconnect it from the wire plug.

The lamp will need to be removed from the socket, which is best done with pliers rather than with bare hands. And then the already known installation in reverse order.

The photo report above gives an idea of how the backlight bulbs are replaced on the Corolla. To replace the backlight bulb, you will need to remove the trunk cover.

A tool for removing the clips that hold this coating will help with this. It is better to remove the light bulb from the socket with pliers, otherwise you can get hurt - the light bulb is small and the glass is fragile. Subscribe to our channel in Yandex.

Replacing headlights and brake lights on a Toyota Corolla. Show. How to change a Toyota Corolla brake light It's very simple - open the trunk and climb into the niche in the wall. How to change the Toyota Corolla license plate lamp It’s also not difficult, but you will need to remove the trim on the rear wall of the trunk.

Are the instructions useful? Yes 5 No.

How to change a light bulb

Answer to the question “How to remove license plate lights on a Toyota Corolla?” is not difficult. To change the light bulb, you need to open the trunk, examine the back door, and you will have to remove the panel fastenings.

When performing the steps to replace the rear license plate light bulbs yourself, stock up on new caps; something will break anyway.

Then the trunk panel is partially detached and the screw securing the light to the car body is turned out. Next, it is pulled out and the electrical connector is disconnected. To get the lamp, you need to remove the light panel by unfastening two fasteners. When changing lamps, it is advisable to observe the sequence of arrangement of wires in the bundle and the correct sealing of the joint. The manufacturer uses 12V 5W bulbs to illuminate the license plate. Difficulties often arise in how to replace a light bulb. It is quite difficult to pull it out, it takes some effort. Just pull. The same goes for installing a new light bulb. You need to take it by the base and press until your fingers go deep inside the lantern.

Replacement e150 body

On a Toyota Coral car, low beam bulbs can be changed in two ways:

Internal replacement.
External replacement.

From the inside

First of all, the hood opens; you can open it from inside the car, after which you need to do the following:

You need to remove the plastic protection that is held on by clips, you can remove them by pressing the middle button at the bottom, as a result of this the mechanism will work and the clip together with the spring can be easily disconnected. You can also pull them out simply by picking them up with a knife or a flat-head screwdriver. When all the clips are disconnected, you can remove the protection.
When the protective cover is removed, access to the headlight unit, which is responsible for the high and low beam of the Toyota Corolla 150, opens. It is much easier to replace light bulbs on the left side than on the right. To remove the low beam lamp, it must be disconnected from the power supply, since its wiring with a plug is inserted into the base itself with a special socket. To do this, the latch is pressed, and the lamp is quietly removed from the base by turning it counterclockwise from the mounting socket.
The new one is installed as simply as removing the old lamp; to do this, the new light element must be taken by the base and installed in its seat; for convenience and correct installation, there are special guides on it. When the lamp is installed in the socket, the base turns clockwise until it clicks, which means that it is locked in the socket. Then the power is connected.

After replacement, you should check the serviceability of the headlights; if everything works, you can put everything back together. If suddenly the light does not come on, you need to check the fuses and relays

It is important to know that when replacing an old light bulb with a new one, holding onto the light bulb itself is not recommended, since there is a high probability that it will fail. It is also not recommended to replace it in high humidity, since trapped moisture can also cause rapid failure of the lamp.

If the right low beam lamp of a Toyota Corolla has burned out, then in addition to the protective casing, you also need to remove the expansion tank. To remove it you need:

Unscrew the two bolts, this can be done using a 10mm wrench, and remove the tank.
In addition to the reservoir, the neck of the washer can prevent you from getting to the light bulb, since it makes the view very poor, but there is no need to remove it, just take a mirror and place it on the side, this way you can see where the lamp is located. Once the location is certain, you can start replacing. It changes in the same way as the left light bulb.

Why does the rear license plate lamp often burn out?

Perhaps due to the increased humidity, the cartridge or antennae have rusted inside. It is necessary to install a new one or clean and replace the conventional incandescent lamp with an LED lamp that is insensitive to moisture.

Long-term shaking, off-road driving, and bumpy roads shorten the service life of standard lamps.

The lighting suffers due to a blown fuse or voltage drops in the car's electrical circuit. The chain may break due to natural wear and tear. These damages can be determined using an ohmometer.

The fuse responsible for the license plate light is called “Tail” 10A. If it burns out, the dimensions will stop lighting.

If, after lightly tapping the rear license plate light, the light comes on, it means there was a bad contact or it was dirty, you need to clean it.

There is also a nuance with the number plate illumination. Normally, during the day it lights up if the trunk is open. When opening the car using the key fob, make sure that you do not open it along with the interior doors. Many car enthusiasts complain about the ever-burning license plate light, which does not go out after 5 or 30 minutes until you turn off the car and remove the key from the ignition. It's all about the trunk lock: either the limit switch is stuck, or the car was opened twice with the key fob, or the chip contains a program for opening all the doors and trunk with one click. A constantly glowing lamp often burns out, and the battery also runs out at the most opportune moment.

LEDs in the license plate lighting of Toyota Corolla e180

On the Toyota Corolla E180, the license plate lighting is too dim in my opinion. For illumination there are two 5-watt W5W bulbs, all lamps are in Corolla. The lampshade is constantly covered with a layer of dust and dirt, and this makes the room illumination even less; in bad weather, at night, you can’t even make out the license plate number.

Therefore, it was decided to replace the weak stock lamps with modern LEDs.

The stock license plate light has part number: 812700D120

To convert to diodes, there are two options:

select a diode with a W5W base;
Completely replace the flashlight with LED matrix.

The easiest and least expensive way is to replace the light bulb with an LED with a W5W base. It is desirable that the diode is CREE

it will last longer than usual and shine brighter. For a long time I have been trying to buy only these LEDs, they shine very brightly and they have a built-in stabilizer, which extends their service life.

I bought these diodes on Ali https://ali.pub/28466v as in the photo below. Sold in packs of 5, not poorly made, I also liked the way they shine. I installed them in my license plate lighting.

List of light bulbs Toyota Corolla 150

The operating instructions contain the following list of lighting lamps for the Toyota Corolla 150:

high beam: bulbs with HB-3 base (12V / 61W);
low: HB-4 (12V / 52W);
dimensions: W5W (12V / 5W);
reverse: P21W (12V / 10W);
License plate light: W5W (12V/5W);
brake light and dimensions: T20 socket, double-spiral lamp (21/5W);
front, rear turn signals: socket type S25, single-spiral lamp 21W / 12 V.

Note to the driver. Before purchasing, it is important to know the year of manufacture of the car. For the first generation and restyling, lamps with different bases are installed, namely: Toyota Corolla 2006 - 2008 (H7, HB3, HB4/H11), 2009 - 2012 (HB4, HB3, H11).

When installing lamps of high power and luminous efficiency, preliminary consultation with specialists is necessary. There are often cases when the size of the base is identical, but the cross-section of the electrical wiring is small. As a result, the cable heats up, burns out, and the insulating layer melts.

Replacing Toyota Corolla lamps (E150)

Repair » Electrical » Lighting system » Toyota » Corolla » Corolla X (E140, E150), 2006 - 2013

Lamps used on cars

Installation location	EAK designation
High beam lamp	HB3
Low beam lamp	HB4
Front turn signal lamp	WY21W
Fog lamp	H11
Front marker lamp	W5W
Side turn signal (on vehicles produced before 2010)	WY5W
Rear fog lamp	W21W
Reversing lamp	W16W
Rear turn signal lamp	P21W
Brake/Tail Light Lamp	W21/5W
License plate lamp	W5W

Replacement of left headlight bulbs is shown. The lamps in the right headlight are located symmetrically; they are replaced in the same way.

To replace the turn signal , follow these steps. 1) Disconnect the wire from the negative terminal of the battery.

7) Install the new lamp into the socket and the socket into the headlight unit.

2) Squeeze the latch.. 3) ...and disconnect the wiring harness block from the turn signal lamp socket. 4) Turn the turn signal lamp socket counterclockwise. 5) Remove it from the headlight unit. 6) Remove the baseless lamp from the socket.

To replace the side light , perform the following steps. 1) Disconnect the wire from the negative terminal of the battery.

2) Squeeze the latch.
3) Disconnect the wiring block from the side light lamp socket
4) Turn the side light bulb socket counterclockwise.
5) Remove it from the headlight unit.
6) Remove the baseless lamp from the socket
7) Install the new lamp into the socket and the socket into the headlight

To replace the low beam lamp, follow these steps. 1) Disconnect the wire from the negative terminal of the battery.

2) Squeeze the latch.
3) Disconnect the wiring harness block from the low beam lamp
4) Turn the base of the low beam lamp counterclockwise.
5) Remove the lamp from the headlight unit
6) Install a new low beam lamp in the headlight and connect the wiring block

To replace the high beam lamp, perform the following steps. 1) Disconnect the wire from the negative terminal of the battery.

2) Squeeze the latch.
3) Disconnect the wiring harness block from the high beam lamp
4) Turn the high beam lamp base counterclockwise.
5) Remove the lamp from the headlight unit
6) Install a new high beam lamp behind the headlight and connect the wiring block.
to replace the side turn signal lamp lamps on a Toyota Corolla; if the lamp burns out, the lamp assembly must be replaced.

To replace the rear turn signal lamp or brake lamp and tail lamp, follow these steps. 1) Disconnect the wire from the negative terminal of the battery.

3) Remove the cover of the access hole in the trunk trim
4) Turn the lamp socket to be replaced counterclockwise.
5) and remove it from the flashlight body.
6) Remove the baseless lamp from the socket.
7) Install the new lamp in the reverse order of removal.

To replace the reverse light bulbs or rear fog light bulbs, perform the following steps. 1) Disconnect the wire from the negative terminal of the battery.

2) Pry it off with a screwdriver
3) Remove the cover of the trunk lid access hole.
4) Squeeze the latch and disconnect the wiring harness block from the lamp.
5) Turn the lamp socket counterclockwise.
6) Remove it from the flashlight housing.
7) Remove the baseless lamp from the socket.
Install the new lamp in the reverse order of removal.

For information

The white light of the lamp (over 5000K) is more aesthetic than practical. In conditions of fog and increased dampness, visibility will remain limited and the effectiveness of such lighting is minimal. Consider this factor when purchasing.

A lighting device with increased brightness serves less than its counterparts with a standard coefficient. If you need additional light, be prepared for a short life.

Xenon lamps are officially prohibited for installation on the Toyota Corolla 150, as well as other modifications. Instead, they are actively installing LED analogues. Of course, they are not comparable to halogen ones, but in low beam they illuminate the road well.

Popular manufacturers of diode lamps for Toyota Corolla: KOITO, GE, MTF, NARVA, OSRAM, PHILIPS, VALEO, DiaLUCH. The cost of original diode ones varies from 7,000 rubles, while Chinese alternative optics offer a cheaper option, for 1,500 – 2,000 rubles.

Sequence of actions when replacing lighting elements on a Toyota Corolla 150

We carry out preventive maintenance in advance, identify faulty elements, and check (call) the electrical wiring as necessary. For such purposes, it is better to use a special device - a multimeter.

Every driver should have it, as it is used to carry out comprehensive preventive maintenance of the electrical power system and troubleshoot problems. If not, contact the service center specialists for help.

We install the Toyota Corolla 150 on a flat surface, turn the steering wheel in the opposite direction of the burnt-out headlight. Use a Phillips screwdriver to unscrew the plastic splash guard. We remove the two latches and lower the mudguard down. We turn the PTF base counterclockwise, remove it, and replace it with a new one. We do not touch the flask with our hands.

How to remove license plate lights on a Toyota Corolla

Zene Even more useful tips in a convenient format.

info. Audi 80 A4 A6. VAZ GAZ Gazelle Kia Rio Sportage Sorento Sid. Opel Astra Vectra.

Renault Duster Megan Logan Scenic. Toyota Camry Corolla Rav 4.

Chevrolet Aveo Cruze Lacetti Niva. Volkswagen Passat Polo Golf.

Ford Focus 1 Focus 2 Focus 3. ?

Replacing High/Low Beam

Carefully remove the plastic protection; it is secured with three clips. If necessary, lightly press with your finger in the center for ease of dismantling. We unscrew the faulty lamp and replace it with a new one. We inspect the integrity of the insulating layer and connectors. If there is damage, replace it with new ones. If the design has a pre-installed control unit, it is also subject to checking for integrity and quality of fixation.

Interior lighting

We carry out the replacement ourselves, the process is simple and intuitive. If difficulties arise, we involve workshop specialists.

Using a flat-tip screwdriver, carefully pry off the outer cover of the lamp. It is tightly fitted to the ceiling trim with three latches. Careless actions or excessive force will damage the plastic, be careful. We remove the cover, remove two diodes, install new ones. Ready.

We carry out troubleshooting of the cover, check the tightness of fit and fixation.

Requirements for rear license plate illumination

Lamp selection

Only certain types of lamp bases are suitable for Toyota Corolla optics. The base itself is designed to fix the light bulb in the housing, as well as transmit current to it.

The best option for the Toyota Corolla 2013 of all is the HB4 Koito Whitebeam 12V 55W from the Japanese manufacturer. This lighting is reliable and very bright. It is especially recommended to buy this brand for high beams. The only disadvantage of Koito is the high price.

The Philips Crystal Vision HB4 is another great option that will glow a very bright white light.

For Toyota Corolla there are several types of lighting that can be supplied, depending on your consumer needs:

All-season.
Durable.
With increased light output.
Blue lighting.

Let's consider the main features characteristic of each of these types of lamps.

All-season

All-season, or all-weather, lamps are best installed by car owners who drive a lot outside the city at night. A special feature of all-season models is that their bulb is covered with a yellow layer. It turns out that the luminous flux of the lamp becomes yellow, which is much more effective than white in humid weather.

How to change a light bulb

When performing the steps to replace the rear license plate light bulbs yourself, stock up on new caps; something will break anyway.

Part 2. Replacing the center console light bulbs

Replacing lamps in buttons To change the lamp for the hazard warning light button, you need to remove the panel with the deflectors, and then pull out the hazard warning button from it. We direct the deflectors as high as possible, under them on the left and right there will be mounting ears, which we pull down with a slotted screwdriver and pull the panel toward ourselves.

There is a socket with a lamp on the side; use tweezers to turn it counterclockwise and pull it out. The light bulb contacts are wrapped around the socket on the sides. The light bulb is small, the size of a match head. These can be found either at radio markets or in radio-electronic component stores.

Marking H, 12V car radio lamp, costs about 20 rubles. It is a little longer and thicker than the original one, but it fits into the cartridge just fine. In the photo they are number 2 red and white, number 3 is the original, number 1 is the center console backlight, for comparison.

To change the illumination lamp of the rear fog lamp button, carefully pry the panel with the button with a screwdriver and pull it towards you. Then everything is the same as in the emergency button. Almost the same lamp is used as in the emergency warning button, but with a green filter cap. I also change this lamp to H, moving the green cap.

VESKO-TRANS.RU

Replacing low beam headlights on Toyota Corolla 120 (2000–2006) and 150 (2006–2013) does not require a professional electrician. This operation is not at all difficult and if you follow the instructions below, you will not be able to learn how to change the light bulbs.

Before you buy new lamps, you need to know what exactly is in the Corolla optics.

For clarity, below is a sketch showing the appropriate lights for the whisk.

Basically! Medium HB4 is not confused with H4

Only certain types of lamps are suitable for Toyota Corolla optics. The base itself is designed to mount the light bulb in the housing, as well as to transmit current to it.

The best option for the 2013 Toyota Corolla is the Ko4 Whitebeam 12V 55W from the Japanese manufacturer. This lighting is reliable and very attractive. It is especially recommended to take this brand in bright light. Koito's disadvantages include only the highest values.

Philips Crystal Vision HB4. Another good option that will give a very eye-catching light white color.

There are several types of lighting for Toyota Corolla, depending on your consumer's needs:

All year round.
Long period.
With increasing light output.
Blue lighting.

Let's consider the main features characteristic of each of these types of lamps.

Weather or all-weather lights are ideal for motorists who travel a lot at night. The peculiarity of the season is that their test tubes are covered with a yellow layer. It turns out that the luminous flux of the lamp acquires a yellowish color, which is even more effective than white in damp weather. While white light is scattered by moist particles in the air, yellow light will not have such a problem: yellow light has a scattering coefficient of less than 20 percent. This will give you excellent visibility in fog, snow or rain.

replacing low beam on Toyota Corolla

Recommended for those who spend a lot of time driving at night. Such lamps are able to work twice as often as usual. Strength is ensured by the vibration resistance of the base and a special gas in a test tube. Manufacturers have these headlights labeled Long Life.

It is recommended that people whose headlights have lost clarity and are more likely to catch fire replace old bulbs. Higher luminous flux (30 percent higher than normal) is achieved due to the higher filament temperature. It may seem that such a thread will burn out even faster, but this will not happen, because a special gas that protects it is released into the test tube.

In fact, their color is close to blue, but traders still call them blue bulbs. Unknown people confuse their light with xenon light because it is indeed similar but not as powerful. This lighting is obtained by spraying blue onto the test tube. The advantage of this light is that his eyes get tired even less than usual.

Replacing License Lamp Bulbs for Toyota Corolla

Long-term shaking, off-road driving, and bumpy roads shorten the service life of standard lamps. The lighting suffers due to a blown fuse or voltage drops in the car's electrical circuit.

The chain may break due to natural wear and tear. These damages can be determined using an ohmometer. If it burns out, the dimensions will stop lighting.

If, after lightly tapping the Toyota Corolla E150 rear license plate light, the license plate light comes on, it means there was a bad contact or it is dirty, you need to clean it. There is also a nuance with the number plate illumination. Normally, during the day it lights up if the trunk is open. When opening the car using the key fob, make sure that you do not open it along with the interior doors.

Source

Toyota Corolla Forum

The photo shows how we pasted it for the first time without a corner, and the light shines past. Next, having chosen the right angle and installed our card with diodes, let's take up the backlight on/off button. Toyota Corolla complete lack of license plate illumination, need to replace light bulbs. We will need a reverse button. It looks like an ordinary button, only it has a reverse action, in other words, when it is pressed, the circuit is open; when there is nothing holding the button, the circuit is closed.

Instructions with video and replacement, replacement of Toyota Corolla license plate light bulb, Toyota Corolla filter, replacement of the cabin filter.

The photo shows an example of that button. And you can change the number plate illumination lamps by replacing the light bulbs. It's easy to do. There is a plug on the left side of the glove compartment when it is open; remove it and take out the glove compartment.

You need to take it by the base and press until your fingers go deep inside the lantern. Why does the rear license plate lamp often burn out? Perhaps, due to precipitation, the socket or antennae inside have rusted. It is necessary to install a new one, in other words, clean it and replace the ordinary incandescent lamp with an LED, insensitive to moisture.

Types of Bulbs in Megan 2 Headlights and Replacement Instructions Producer Renault completed the Megan 2 headlights, which combined lights for passing, driving, turning and parking. Separately, in the lower part of the front bumper, if provided in the kit, fog lights are installed.

The rear lights are equipped with brake lights, parking lights, turn indicators. Is your VAZ stove not heating well? In summer, heating is not required, therefore, using a special faucet, the Toyota Corolla license plate light bulb of the heater radiator is replaced from the water supply system, which comes from the general cooling system. Whereas in winter, replacing the timing belt of Mitsubishi Pajero 3.

Long shaking, off-road driving, and bumpy roads shorten the service life of standard lamps. The lighting suffers due to a burnt fuse or voltage drops in the car's electronic circuit. There is a possibility of a broken chain and therefore natural wear processes.

These damages are determined using an ohmometer. If it burns out, the dimensions will not shine.

How to remove license plate lights on a Toyota Corolla

If, after lightly tapping the rear license plate light, the light comes on, it means there was a bad contact or it was dirty, it needs to be cleaned. There is also an aspect with number plate illumination.