How to change the light bulbs in the Camry 40 license plate light?

Lamps used in Toyota Camry xv40

Owners of the "magpie" often complain about poor low beam. You can solve this problem by adjusting the headlights or replacing the light bulbs. We talked about how to adjust the optics and fog lights of the Camry 40 in this material.

In the manual for Toyota Camry 2006 - 2011 there is a table containing information about electric lamps.

Detailed information about light bulbs used in optics and flashlights of Toyota Camry XV40:

• high beam - HB3,
• side lighting and license plate illumination – W5W,
• low beam - halogen H11, gas discharge D4S (xenon),
• front and rear turn signals – WY21W,
• fog light – H11,
• rear brake light and dimensions – W21/5W,
• reverse gear – W16W,
• rear fog lamp – W21W,
• side turn signal (on the body) – WY5W.

The letter “Y” in the lamp labeling indicates that the lamp color is yellow. The manufacturer does not provide for replacing the bulbs in the side direction indicators; the lamp is replaced as an assembly.

Bulbs used in Camry 2009 interior lighting:

• general lighting, central lamp – C5W,
• light for driver and front passenger - W5W,
• lamp in the sun visor – W5W,
• glove compartment lighting – T5,
• cigarette lighter bulb – T5 (with green filter),
• automatic transmission selector travel light – T5 (with filter),
• front door opening lighting – W5W,
• trunk lamp - W5W.

Halogen, xenon (gas discharge) and LED bulbs

The 2007 Camry was equipped with halogen lamps from the factory. Advantages of this type of bulbs: accessibility compared to other automotive light sources. Halogen lamps do not require the installation of additional equipment (ignition units, headlight washers). Variety, this type of lighting has been used for decades, so there are a large number of reliable manufacturers producing high-quality products. The light is not of poor quality; in terms of luminous flux characteristics, halogens are inferior to xenon and diodes, but provide acceptable road illumination.

Disadvantages of halogen lamps: low brightness compared to xenon and LEDs, which provide better visibility at night. Low efficiency, consume a large amount of energy without producing a bright luminous flux. Short service life; on average, xenon lamps will last 2 times longer, and diode lamps 5 times longer. Reliability is not high; halogen lamps use an incandescent filament, which can break if the car is shaken.

When choosing halogen bulbs for the Camry XV40 2008, following a few rules will allow you to buy a quality product that will ensure driving safety in the dark:

• choose trusted manufacturers,
• use high-brightness lamps from 30 to 60 percent,
• pay attention to the service life specified by the manufacturer,
• do not buy lamps with a power higher than 55 W,
• Before purchasing, check the light bulb for visible damage.

Xenon lamps

In rich configurations of the Toyota Camry 40, the dipped beam is xenon; many owners of a magpie with conventional optics install xenon. One of the options for how to do this is described here.

Which light bulb should I install?

On both versions of the car body, a W5W lamp is installed - its catalog number is 2825 or 168. The nominal voltage of the lamps is 12 volts, power consumption is 5 Watts. There are more powerful light bulbs produced in a similar form factor, but it is not recommended to use them to illuminate rear license plates - the heat emitted during their operation will eventually lead to dimming and deformation of the plastic lamp. The best option would be to purchase modern LED lamps - with a similar level of glow, their consumption is 8–10 times less than that of an incandescent lamp, and there is practically no heat generation. In addition, their service life is several times longer than the service life of an incandescent lamp, which means that replacing license plate light bulbs on a Camry 40 or 50 will be required much less frequently.

Important! According to clause 12.4 part 2 of the traffic rules, only white-yellow and yellow lamps can be used to illuminate the number. The use of blue, green or red lamps is punishable by a fine of up to 5,000 rubles.

But you cannot operate a vehicle without license plate illumination at all: this violation is punishable by a fine of 500 or a verbal warning from a traffic police inspector. A violation is either completely faulty lighting or just one non-working light bulb. Timely replacement of the license plate illumination on the Camry v50 and any other bodies will allow you to avoid drawing up a report and the costs associated with paying a fine.

Replacing lamps on Toyota Camry 40

You don't need any tools to replace the low and high beam bulbs on your 2009 Camry. Let's start talking about changing lamps from low beam. The low beam lamp is located in the center of the headlight unit. We turn the base counterclockwise and remove the light source from the headlight, disconnect the power by pressing the latch. We install the new lamp and perform the assembly in reverse order.

Do not touch the halogen lamp with bare hands, the remaining traces will lead to rapid burnout. You can erase prints with alcohol.

The high beam lamp is located on the inside of the headlight unit. Replacement occurs according to the same algorithm as for changing the low beam lamp. We unscrew it counterclockwise by pressing the lock, disconnect the lamp, install a new one and assemble it in reverse order.

Replacement of the parking light bulbs and turn signal of the Camry 2010 is carried out from the side of the wheel arch. To gain access to the light fixtures, turn the wheels away from the headlight, use a flat screwdriver to remove a couple of clips and bend the arch protection. We have two connectors in front of us: the top black one is the marker, the bottom gray one is the turn signal. Replacing these lamps is not much different from the previous ones.

Quick replacement method

To do this, the car owner will only need a 3 mm hexagon and, in fact, the light bulb itself.

The sequence of actions is as follows:

1. The hexagon is inserted into a special hole located on the side of the license plate light.
2. Then the key must be pushed sharply, but without excessive force, towards the Toyota logo located on the trunk lid.
3. When the cover comes off the guides, stop putting pressure on it and then pull it out with your hands.
4. Remove the old backlight lamp from the socket and install a new one.
5. Replace the cover and snap it into place.
6. The lamp in the second lampshade is changed in the same way.

It is worth noting that, regardless of the body type of the Toyota Camry, replacing the license plate light bulb using this method can be done in less than a minute. The risk lies in the possibility of breakage of the plastic fasteners of the lampshade due to excessively strong pressure applied during its dismantling. It is also necessary to take into account that on the lid, the holes for the hex key are located on both sides, but for dismantling it is necessary to use only the outer ones, and the lid itself should be shifted towards the center of the trunk, focusing on the automaker’s logo. When the lamp cover is moved towards the lights, it may fall under the “saber”. Removing the cover may require removing the taillights.

Replacing lenses on Camry 2011

To replace a faded lens on a Camry 40, you need to disassemble the headlight. You can open the optics by heating the junction of the body and the lens in a circle with a hair dryer; be careful not to melt any element. The second method is to unscrew all the screws, remove the anthers and plugs, metal parts from the headlight, and place it wrapped in a towel in an oven preheated to 100 degrees.

After warming up the optics, begin to carefully remove the housing from the lens using a flat-head screwdriver. Take your time and gradually open the headlight. If necessary, warm up the optics again.

The sealant will form fibers that should not get into the inside of the optics. After opening the headlight, while it is hot, glue all the threads of sealant onto the headlight housing or lens.

The lens is attached to the body with three clamps, open one of them and carefully squeeze out the lens. Buy lenses with transition frames, which will greatly simplify your work. We replace the lens with a new one and wipe it with a 70% alcohol solution. You can remove dust and debris from the internal parts of the headlight with a dry, lint-free cloth.

Acetone should not be used! May damage surfaces of parts.

You cannot change the lower edge (cut line) of the shield slot; you will blind oncoming people.

The lens is in place, preheat the oven and place the headlight, wrapped in a towel, in there for 10 minutes. We remove and press the glass against the body, do not overdo it, the glass may crack, it is better to repeat the procedure 3 times. The glass is in place, screw in the screws and continue in the oven for 5 minutes.

Replacing front light bulbs

How to change the low beam light bulb on a Camry ? It is located in the middle of the headlight structure. The base of the lamp must be rotated counterclockwise approximately 90 degrees. After this, remove the headlight cover and remove the failed bulb from under it. Then, by lightly pressing the latch, the electrical contacts are disconnected.

A new light bulb is connected to the corresponding connector, the headlight is inserted, which is carefully turned the same 90 degrees, but clockwise until fully installed.

Before changing the fog light bulb in a Camry , you should take precautions. It is advisable to carry out this operation with gloves so as not to touch the surface of the inserted light bulb with your fingers. Otherwise, fingerprints may cause the lamp to burn out prematurely.

If the new lamp becomes dirty, you need to carefully wipe the glass surface with a cloth soaked in alcohol.

Replacing a light bulb using a safe method

For ease of use, it is recommended to prepare a regular flat-head screwdriver and a new light bulb. Execution algorithm:

1. Open the trunk.
2. Find the location of the fastening clips that secure the casing.
3. Pry up and remove the latches located next to the rear license plate lights.
4. Unscrew the decorative covering.
5. Disconnect power supply (connectors).
6. Slide the lamp out of the base.
7. Use your fingers to carefully press the latches.
8. Remove the device.
9. Remove the cover.
10. Replace the light bulb with a new one.
11. Install the parts in their original places.
12. Restore the casing using fixing clips.

This procedure takes approximately no longer than 20 minutes. When working, accuracy and caution are required. This is especially true for releasing fragile plastic fasteners.

Tip: It is recommended to replace license plate lamps in pairs. This is necessary to ensure lighting with the same intensity and overall color scheme.

How to change headlight bulbs on a Camry

This operation is most conveniently carried out from the wheel arch. First, you need to turn the car wheel using the steering wheel. If the light bulb is changed from the passenger seat side, then to the left. If from the driver's side, then to the right. After this, the protective fasteners are removed and the protection itself is carefully rotated. As a result, access to the side lamps is organized.

Now we begin to solve the main problem - how to change the side light bulb on a Camry 40 . It is located on top of the turning lamp socket. It has a gray color. The failed marker light bulb is rotated 90 degrees counterclockwise and pulled out of the connector. After this, the new light bulb is inserted into the socket and rotated 90 degrees clockwise until it is completely locked.

It is also extremely undesirable to touch the glass surface of the side light bulb with your fingers.

Installation of high beam lamps

The high beam bulb is located inside the corresponding headlight. It is replaced in almost the same way as the low beam bulb. The old light bulb is carefully turned ninety degrees counterclockwise and pulled out of the socket. The new one is installed in its place; to do this, it is rotated in the connector in the opposite direction at the same angle.

Replacing a turning lamp in a Toyota Camry 40

Like the side lamp, it is located behind the wheel arch. Accordingly, it is accessed in the same way. The rotating light bulb has a light gray socket; it itself is located slightly lower than the overall light bulb and is slightly larger in size. To replace it, you need to turn the socket counterclockwise and remove the failed lamp. After this, the new light bulb is inserted into the socket, then the entire structure is placed in the headlight and rotated 90 degrees clockwise.

How to change license plate lights on a Camry

The vehicle license plate must be visible at any time of the day, including at night. Therefore, when darkness sets in, it is necessary to illuminate it. If the license plate light bulb has burned out, it must be urgently replaced. On Camry 40 and 50 it is carried out quickly. In order to get to the failed lamp, you need to move the trunk trim a little.

After this, use a flat screwdriver to remove the clips of the protective upholstery. Its edge should be slightly bent, after which we gain access to the lamp socket. We remove the battery, unscrew the burnt-out lamp (also counterclockwise 90 degrees), insert a new lamp into the connector. Next, perform all the described steps in reverse order.

A few tips for car owners

• If fuses or light bulbs constantly blow on a car, then it is necessary to check the voltage of the car’s on-board network - it is quite possible that the generator is failing.
• Replacing license plate light bulbs on Camry 50 and 40 should be done in pairs and it is not recommended to install bulbs of different wattages or colors.
• You can immediately purchase several light bulbs and carry them in the glove compartment of your car - if the lamp fails, it can be easily and quickly replaced right on the spot. This will help avoid a fine.
• If the lamp cover is damaged during replacement, then do not be upset - you can buy it at the nearest auto repair shop at a low price. In addition, it is not necessary to purchase a cover specifically for the Camry - almost all “Japanese” cars have the same lamps installed.

As you can see, replacing license plate lamps on a Camry in the 40 body, as in the 50, does not take much time and effort. Therefore, it is better to do it yourself, saving 400–500 rubles.

• Tweet
• Share 0
• Reddit
• +1
• Pocket
• LinkedIn 0

Top

How to change front lamps on a Toyota Camry

You don't need any tools to change the low and high beam bulbs. But to gain access to the front marker and turn signal lamps, you will need a small flat-head screwdriver.

It will be much easier to change the turn and clearance lamps from the wheel arch . To do this, you need to turn the steering wheel (and the wheel, respectively): to the left if the replacement occurs on the passenger side, and to the right if the lamps are changed on the driver’s side.

Then you need to remove at least two fastenings of the protection in the wheel arch, and unscrew the protection, gaining access to the lamps.

Replacing low beam lamp Camry V40

The low beam bulb is located in the center of the headlight assembly. Turn the base of the lamp a quarter turn counterclockwise and remove the lamp from the headlight. Then press the latch and disconnect the power connector.

The new lamp should be connected to the connector, inserted into the headlight and turned a quarter turn clockwise.

An example of replacing lighting on different cars

• clean the area where the lampshades are located from dust and dirt;
• remove decorative trim;
• clean the surface of the lampshades;
• unscrew the screws;
• remove the lampshades;
• remove the lighting fixture;
• make sure it is faulty;
• replace light bulbs with new ones;
• check the functionality of the unit by turning on the lights;
• secure the lampshades by first lubricating the screws with silicone grease;
• Reinstall the fastening of the trunk lid trim.

The basic algorithm for replacing license plate lamps can be changed depending on the make and type of car.

Hyundai Santa Fe

• Unscrew the self-tapping screw holding the backlight;
• remove the lampshade by releasing the lock;
• remove the illuminator, taking into account the short length of the supply wire;
• carefully turn the cartridge counterclockwise;
• remove the socket together with the lamp;
• pull the last one out of the cartridge;
• install a new light bulb;
• return the cartridge to its place, fixing it by turning it clockwise;
• install the lampshade and secure it with a self-tapping screw.

Both lamps, which provide room illumination, are located in the Hyundai Solaris under the trim on the trunk lid. To remove them, you need a flathead and Phillips screwdriver. The dismantling process looks like this:

Volkswagen Tiguan

• open the trunk lid;
• remove the lampshades by unscrewing the screws;
• unplug the light bulb from the spring clips;
• install the new device by snapping it into the latches;
• return the lampshades to their place and secure them with self-tapping screws;
• check the result using the side lights.

To get easy access to the backlight lamp of this brand, you will have to lower the flashlight diffuser down. To do this, you will need to lightly press the tongue.

Further actions are performed in the following order:

We recommend videos on the topic:

To replace the backlight bulb in a Japanese Toyota Camry, you need a flat-head screwdriver. Lamps - W5W. Then follow these steps:

Nothing other than screwdrivers is required to replace license plate lamps in a Nissan Qashqai. In addition to traditional insulation of the on-board electrical system, perform the following steps:

Installing a new headlight bulb on a Lada Priora is simple and does not take much time. To restore room lighting, you need to:

We recommend watching a video on the topic:

Location of Toyota Camry lamps

*The letter "Y" in the name indicates that the color of the lamp is yellow, although in reality the color of the lamp is orange.

We recommend replacing all low beam lamps in your vehicle. Otherwise, differences in brightness and other light characteristics may disturb the driver and other road users.

Bulbs used in Camry

High beam Camry v50 H11

• GE H11-12-55 (General Electric) 53110 from 500 rub.
• KOITO H11-12-55 0110K from 500 RUR
• MTF H11-12-55 30% standard long life x4 HS1211 from 300 RUR
• OSRAM H11-12-55 64211 from 550 RUR
• PHILIPS H11-12-55 LLECO VISION (4x Resource) 12362LLECOC1 from £55
• VALEO H11-12-55 Standard 032525 from 480 RUR
• DiaLUCH H11-12-55 PGJ19-2 Prime 12511PR from 300 RUR
• SUNRISE H11-12-55 80 192 from 120 RUR
• H11-12-55 LONG LIFE 48078LL from 470 RUR

• AVS H11-12-55 110% 3700K Sirius Night Way from 600 rubles
• KOITO H11-12-55 W (100 W) Set of another brand from 2000 rub.
• OSRAM H11-12-55 NIGHT BROKER 110% PROTECTED 64211NBU from 1500 rub.
• OSRAM H11-12-55 60% SILVERSTAR 2.0 (2x resource) from 1400 RUR
• DiaLUCH H11-12-55 100% 4000K PGJ19-2 12511ELSDUO from 600 RUR

Low beam lamp Camry

When choosing standard xenon lamps for the Camry V50, do not confuse D2S and D4S lamps; these are different lamps. The D2S lamp will not work on a Camry.

To replace a low beam lamp, it is necessary to study the design of the headlight in the car, as well as select the correct type and power of the emitter. Causes of problems with headlights. If the low beam is not working, you should not immediately run to a specialized store for a new halogen or xenon bulb, especially since it may have a high

In order to replace low beam lamps on a Toyota Camry, you must perform the following procedure:

Replacing the high beam lamp Camry V40

The high beam lamp is located in the inner corner of the headlight assembly. It changes in the same way as the low beam lamp. You need to turn the base of the lamp a quarter counterclockwise, remove the lamp and disconnect the connector. Install in reverse order.

Replacing the Camry V40 clearance lamp

The marker lamp is located just above the light gray turn signal lamp socket, and has a black base. Turn the lamp 1/4 turn counterclockwise, remove the lamp and remove it from the socket. Then insert the new lamp into the socket, install it in the headlight and turn 1/4 clockwise, fixing it.

Replacing the turn signal lamp Camry V40

The turn signal lamp has a light gray socket and is located under a slightly smaller marker lamp. To replace, you need to turn the socket counterclockwise, remove the old lamp and replace it, install the socket with the new lamp in the headlight and turn it 1/4 clockwise.

Quick replacement

It uses a 6x3 polyhedron and a new lamp. Procedure:

1. Insert the tool into the hole near the lampshade.
2. Slide the key towards the Toyota logo (on the trunk lid).
3. Remove the cover from the guides, remove it manually.
4. Replace the burnt out light bulb with a new one.
5. Place the lamp in its original position.
6. Repeat the steps with the other lampshade.