How to reset T-belt Tech Doc Toyota message

Step-by-step instructions - Resetting the T-Belt indicator: Set the speedometer mode to ODO and turn off the ignition. While holding the trip computer switch pressed, turn on the ignition for 5 seconds. Release the switch and press it again after 5 seconds. Switching the display to T-BELT mode is accompanied by the display of data on the vehicle's mileage at the time of the last belt replacement. Note: If the odometer was replaced before the belt was replaced, the odometer reading will not be accurate. We set a new value (mileage) to replace the timing belt. Set the display to whatever value you want.

The T-Belt light came on and the question arose: how to put it out, the belt was changed 40 thousand ago. I did the following: 1) Inserted the key, pressed the odometer button, without releasing it, turned on the ignition and kept the button pressed, released the button and turned off the ignition. 2) After 5 seconds - sleep So we exchanged tyrs! The T-Belt light came on and the question arose: how to put it out, the belt was changed 40 thousand ago. I did the following: 1) Inserted the key, pressed the odometer button, without releasing it, turned on the ignition and kept the button pressed, released the button and turned off the ignition. 2) After 5 seconds - pressed the button again and then turned on the ignition, holding it for the same seconds, then released it and after a second pressed the button again.

reset T-BELT valera Toyota Hiace after t km the T-BELT light is on, then I did it as expected. Reply to message. Re: reset T-BELT Pavel T-BELT means replacing the timing belt. To make the light go out you need to: Remove the rubber plug on the speedometer and press the button with a toothpick. Reply to message. on the forums Increasing ground clearance for Nissan Hell (3) Nissan power steering (1) Nissan does not go uphill Nissan Safari what to do (1) Nissan repair (1) Daihatsu electronics diagram (5) Mazda Toppo Bj Wide (1) Mitsubishi battery began to boil ( 14) Toyota Buying a car C.

As far as I know, the trip computer is on 4-liter cars, not all diesel cars have it, on new cars it seems to be on all of them after a year. Posted on January 29 - There are no holes where the bolt can be twisted. I want to change the timing belt, in connection with this I have a question:

How to reset T-BELT TOYOACE 97g?

Club of fans of minibuses and minivans Cars change, friends and forum remain And how to do it myself, I’ve also been trying to find the answer for a long time. Here's what else I can add on the high side. I also got to the digital instrument cluster, removed it, disassembled it, cleaned the dust and removed the deposits on the glass from the time of the king of peas, it’s also interestingly designed - concave mirrors, black velvet edging. The bell also turns on with a self-tapping screw. These are the observations, I took pictures, then I’ll post them somehow, I’ll go, I need to work. Last edited by admin on March 14, Apparently when they reset the E-belt, the speedometer was also caught.

He lies about a km from the real speed - he shows less. Nissan and Mazda clone AD-shki. There are two holes in the ignition switch next to the same light bulb, in one of them there is a screw. The book discusses the option of removing the panel with an analog panel, turning a certain screw from one socket to another, I understand that with a digital operation the operation should not be unnecessarily complicated, but how? Find your way around the ignition switch Added after 5 minutes 55 seconds: Any nerd who drives into a jeep becomes a decent mathematician. There are no holes where the bolt can be twisted.

Here is a photo of the dashboard, body of a Toyota Hiace 98. All messages 1 day 7 days 2 weeks 1 month 3 months 6 months 1 year Sorting field: Author Posting time Title Order: I used the old original speedometer, but now I have an optitron with a Grand High, I was moved with an electrician from a regular one to an optitron I already I think maybe something is not connected or connected incorrectly.

T belt Toyota hilux surf, what does it mean?

The difficulty here is that this word is not the surname of some engineer, not the name of the daughter of the main investor of the company, not a reference to a geographical name, but the result of the creativity of Toyota marketers. That is, a word invented specifically for this pickup truck. Therefore, first it’s worth understanding where the word Hilux came from and what it means. The official Internet blog of the British representative office of the Toyota brand helped us with this. According to the information posted there, the word Hilux comes from a combination of the words High and Luxury - therefore, something like “high-level luxury”, if you take the underlying message literally.

A logical question arises: what does the concept of “luxury” have in common with a utilitarian, indestructible pickup truck, which is designed for hard dirty work, and not for fashionable social parties? The British office of Toyota also has an answer to this question. It turns out that the word luxury in this context should not be taken literally - it is a reference to the very first generation of the model, the chassis of which for the most part consisted of components more typical of a passenger car. Released in 1968, the first-generation Hilux received a double-wishbone independent front suspension and a four-speed manual transmission with a steering-wheel-mounted shift knob (like the automatic transmission on many old “Americans” or the manual transmission on our native Volga GAZ 21). The car had rear wheel drive. So, in general, the name Hilux symbolized “a tall pickup truck with the behavior of a passenger car.”

Knowing where this word came from, it is easier to understand how to pronounce it correctly. At the Russian office of Toyota we were told that it would be correct to pronounce this name as “Hilax”, which is further confirmed by a spectacular advertising video starring the famous stuntman Martin Ivanov.

However, in the “folk” version, another pronunciation option is also very popular - “Hilux”. And it’s not just popular, but literally puts Hilax on both shoulders: judging by the statistics of Google queries, the search for the “Hilax” option produces 26,200 results, and for the “Hilux” option - 378,000 at once! So who is right? In an amicable way, the truth in this case lies with the representation. Indeed, in the full version of the word luxury, the first vowel u is read as “a,” which any dictionary will confirm. Accordingly, the same sound should remain in the shortened version. Moreover, in the English language there is an independent word lux, which is read as “laks” and means the same “luxury”. The problem is that the same word lux also denotes a physical quantity, which in Russian has long been known as “lux”. Hence all the confusion! At the end of lux, a Russian speaker sees exactly lux - either a service class or a unit of illumination measurement. The associations are too strong. Another thing is that in the case of Hilux, you should forget about them - after all, this is, in fact, a new word, so it is still more correct to pronounce it according to the established rules of transcription, that is, “Hilax”. The only thing that haunts me is the same Google statistics: if the trend continues, then at this rate in the next generation Hilux will indeed become a “Hilux” - this will be called “transmission by tradition.” But until this happens, we suggest sticking to a more competent option. Toyota Hilux CORRECT: Hilux WRONG: Hilux, Hilux (this also happens). In previous issues: What is the real name of the founder of Tesla? How did Toyota become Toyota? Hyundai Tucson... "Tucson"? "Taxon"? Huayra... How to pronounce this in polite society? Which is correct - “Mazda” or “Matsuda”? Which is correct - “Hyundai”, “Hyundai” or “Hyundai”? "Mercedes" or "Mercedes"? "Mitsubishi" or "Mitsubishi"? "Lamborghini" or "Lamborghini"? Gallardo or Gallardo? "Porsche" or "Porsche"? "Logan" or "Logan"? "B-Em-V" or "B-Em-Double-U"?

T belt how to extinguish

Resetting the T-Belt indicator

a) Set the display mode “ODO/TRIP” (trip meter/trip computer) to “ODO” mode and turn off the ignition. b) While holding the trip computer switch pressed, turn on the ignition for 5 seconds. c) Release the switch and press it again after 5 seconds. d) Switching the display to the “ТBELT” mode is accompanied by the display of data on the vehicle’s mileage at the time of the last belt replacement: – for example, in kilometers 15 (thousand) – in miles: 9 (thousand)

Note:

If the odometer was replaced before the belt was replaced, its readings will not be accurate.

In a number of Toyota Land Cruiser engines, the timing belt (gas distribution mechanism) synchronizes the crankshaft and camshaft. Land Cruisers are equipped by the manufacturer with a warning system about the approaching expiration date of a part. The Toyota Prado 90 t belt indicator on the dashboard lights up at 100,000 km.

Reset t belt nissan

What does T-Belt mean?

The timing belt is a consumable part of the engine with a limited service life. It must be changed, according to technical regulations, after a certain mileage or time period.

The vehicle manufacturer recommends changing the belt and roller every 100–150 thousand km during normal operation of the Land Cruiser. These values are entered into the on-board computer program. When the mileage approaches the set number, the indicator on the instrument panel lights up.

The T Belt inscription notifies the car owner about the need to replace the timing belt.

Why change the timing belt

A design feature of some Land Cruiser engines is the dependence of the power unit on the timing belt. It synchronizes the operation of the gas distribution mechanism. A broken part can lead to serious engine damage. Valves and pistons fail. In severe cases, the engine is completely damaged.

In a number of engine models, if the belt breaks, the valves and pistons do not collide, but the car cannot start and move.

Reasons for replacing the timing belt:

the part has reached the service life recommended by the manufacturer;
replacement of faulty timing elements;
visual inspection revealed external damage;
weakened tension;
when purchasing a used Toyota Land Cruiser.

Under severe operating conditions of the machine, the belt wears out after 50–60 thousand km, which must be taken into account.

If the car is used rarely, when the mileage is up to 100,000 km, the part needs to be changed every 4 years.

How do I turn off the T-Belt warning light?

The alert indicator lights up when the mileage approaches the preset mileage. After replacing the belt, you need to enter new data, and the light goes out.

If the old indicator is not reset or incorrect information is entered, the T-Belt icon will continue to light.

To reset the t belt on Toyota Land Cruiser 100 and Prado J90–120, you need to:

Turn on the ignition.
Move the speed and distance indicator to the ODO position - press the on-board computer switch (button) until the total mileage appears.
Turn off the ignition.
Keep the button pressed and simultaneously turn on the ignition for 5 seconds.
Release the button and turn off the ignition for 5 seconds.
Press and hold the switch again for 5 seconds. with simultaneous switching on of the ignition.
Release and after 1 sec. press the button again - a 2-digit number appears on the display.
Release the switch.
Apply short pressure to set the required distance. One unit is equal to 10,000 (10=100 thousand).
Press and hold the button for 5 seconds. A number with the total mileage will appear on the display.
Turn off and turn on the ignition.

vss45 › Blog › Remove the T-Belt icon from the tidy

After completing all operations to replace the timing belt, it is necessary to set an automatic warning about replacing the belt on the dashboard

The recommended mileage before replacing the belt is 100 thousand, however, given that, as a rule, the actual service life of the engine is greater than the actual mileage (traffic jams, warm-ups, etc.), it is necessary to issue a warning a little earlier, about 90 thousand, although the manufacturer himself is laid with a reserve for a slightly longer mileage, cases of belt breaks known to me begin somewhere around 120 thousand km

On Pradobraznykhs with a mechanical odometer, manufactured before 06.1999. T-Belt zeroing is performed by twisting the screws from one socket to another on the dashboard circuit board, which involves disassembling the dashboard itself

In this article I will only touch on the operation of resetting the T-Belt on a Prado, produced from 06.1999 to 2002 with an electronic odometer - the so-called “restyle”

The primer gives the following sequence of actions:

However, having encountered a translation that is not entirely clear, and having spent some time on unsuccessful attempts, I offer you my version of the sequence of actions:

1. All operations are performed with the engine not running without any disassembly with one button on the dashboard and turning the ignition on and off with the key

2. I have a turbo timer installed in the alarm and it is configured in such a way that when the doors are closed and the ignition is turned off with the key while the engine is running, it immediately goes off, but when at least one door is open, the turbo timer does not turn on on its own. In addition, I still have the original alarm. , activated from a button on the key, stitched into the brain at the factory, it was troublesome to remove it and I left it as an additional one - it may be inconvenient to have two independent signals, but I’m already used to it. Therefore, all actions with the odometer must be performed with with the driver's door open and the alarm turned off

3. The success of the operation directly depends on the time interval of pressing the button and turning on / off the ignition with the key, therefore, if it says “5 seconds”, then you need to hold it for 5 seconds, not 4 seconds and not 6 seconds, I personally use a timer on my phone - it helps a lot to decide on time)))

So, let's get started: 1. turn on the ignition 2. use the button to select the odometer reading mode where the ENTIRE mileage is displayed, ignore the other two modes where the daily mileage is displayed 3. turn off the ignition with the key 4. Press the button and keep it pressed, turn the ignition to 5 with the key seconds 5. release the button 6. turn off the ignition with the key 7. after 5 seconds press the button again, hold it and turn on the ignition with the key, hold the button pressed for 5 seconds 8. release the button and after 1 second press it again - a two-digit number 9 pops up on the display release the button 10. briefly press the button once several times for no more than 1 second, each press increases the number on the odometer by one, each unit is 10,000 future mileage 11. numbers from 00 to 15 run cyclically in a circle, we achieve the reading of the number 09 , i.e. after 90,000 km, the T-Belt inscription on your dashboard will light up and remain constantly lit, reminding you of the need to replace the belt 12. press the button and hold for 5 seconds, the readings on the display should return to the total mileage display mode, release the button, the T-Belt light should go out

And that’s ALL - we drive and rejoice, the T-Belt icon has a poisonous orange color and is very striking - you won’t miss it, whereas if it is constantly on for those who are too lazy to remove it - the eye “blurs” and you stop paying attention to it

Reflections on the topic of timing:

Of course, a belt mileage of 100 thousand is conditionally guaranteed exclusively by original timing parts - the cost of a belt, roller, roller axle with washer, tensioner is not at all astronomical, unlike the cost of the head, pistons, connecting rods and valves that must be replaced during the “fist of friendship”, the following behind a broken belt Different companies and at different times could supply timing parts and belts to the Toyota assembly line, but the Toyota inscription and the original Toyota part number on the spare parts are required. I personally am not one of those who like to save on replacements for the original, which I advise you too - the price of risk is quite high Moreover, now all sorts of hustlers have established themselves under the guise of original parts in Toyota boxes and at Toyota prices to sell us a Chinese counterfeit, so even if you buy supposedly the original, it’s not at all a fact that you won’t get Uncle HuiWinBin’s handicraft, slapped on your knee in Province of KosoKaka

Are there differences in the reset process on different Toyota Land Cruiser models?

Some Land Cruiser models produced before 1999 have a mechanical odometer.

To reset the T Belt on a Toyota Prado 90, you need to tighten the screw on the electronic dashboard plate. There are 2 holes on the back of the panel in the upper right corner. One has a screw screwed in, the other is loose. The instrument panel is pre-disassembled.

Similar steps for resetting t-belt data on the Land Cruiser 80. A number of models have a hole on the dashboard with a plug, opposite which there is a reset button. Using a sharp long object (knitting needle, toothpick) you can press the mileage switch. The data is reset and the icon goes out until the next 100,000 km.

Toyota Land Cruiser 100, 200, left- and right-hand drive, are unified with Prado J120, J150 crossovers. They are equipped with identical electronic odometers. Therefore, the T Belt reset occurs according to the standard principle. Variations in the progress of work depend on the type of ODO and the version of the on-board computer.

Detailed information is contained in the vehicle operating instructions.

The T Belt light on Toyota Land Cruiser vehicles comes on when the timing belt is due for replacement. Previous mileage data is not automatically reset. You need to reset the information after each installation of a new belt. The procedure for resetting electronic odometers is almost the same. Changes in the progress of work depend on the series and year of manufacture of the car.

If you are the owner of this car, then you may have encountered a problem when, after a certain mileage, the T-BELT lamp on your dashboard came on.

According to the instructions, the light coming on warns that the timing belt needs to be replaced. However, there are cases that “T-BELT” lights up even after a recent timing belt replacement.

There may be two reasons:

1. It’s really time to replace the timing belt based on mileage. 2. After replacing the timing belt, the car service forgot to update or incorrectly set a new replacement date for the gas distribution mechanism.

In this article we will tell you how to independently solve a problem with the T-BELT indicator on the Toyota Land Cruiser dashboard at home.

Step-by-step instructions - Resetting the T-Belt indicator:

Set the speedometer mode to ODO and turn off the ignition.
While holding the trip computer switch pressed, turn on the ignition for 5 seconds.
Release the switch and press it again after 5 seconds.
Switching the display to T-BELT mode is accompanied by the display of data on the vehicle's mileage at the time of the last belt replacement.
Note: If the odometer was replaced before the belt was replaced, the odometer reading will not be accurate.
We set a new value (mileage) to replace the timing belt.
Set the display to indicate how far you want to drive before your next timing belt replacement. Pressing the switch once changes the mileage value by one. One unit is equal to 10,000 km. If you set the value to 6, then the next timing belt replacement will be in 60 thousand km. For original parts we recommend setting the value to 10, i.e. 100 thousand km.
After setting the required mileage, wait 30 seconds and hold the switch for 5 seconds.
Make sure the display returns to ODO mode, turn off the vehicle's ignition and start it again. The T-BELT light should go out.

Helpful information!

If the reason for the T-BELT indicator to light up is a scheduled timing belt replacement, we recommend replacing the following parts in order to save money:

timing belt
oil seals
hydraulic tensioners
rollers

How to reset an error (CHECK ENGINE) on a Toyota RAV4

The maint reqd display lights up. What does this mean and how is it eliminated? Unfortunately, we do not have the concept of the next maintenance, and there is no information about resetting in the book I have. Just Alex Insert nickname Quote.

How to reset the T-BELT indicator on a Toyota Land Cruiser Prado 150

Let me clarify from the previous message - this inscription means the onset of the next service interval - it is reset simply: With the ignition on, without starting the engine, we transfer the odometer readings with the button to the total mileage readings. In this position, press and hold down the odometer button. While holding the button, turn off the ignition, wait a second. After turning on the ignition, the “Mine Recovery” sign will blink several times and go out.

Release the button and turn off the ignition.

How to reset T-BELT on the Surf 185 tidy?

Hello, after replacing the timing belt with a 1KZ (Surf 185), when the number 200000 appeared on the speedometer, this Infection came on, tell me how to turn it off.

If your memory serves you correctly, then you remove the dashboard, there is one single outer bolt at the back, and next to it there is a hole under the same one, so you unscrew it and screw it into another.

Resetting the T-Belt indicator (type 3 - electronic odometer) Print and PDA version

Adjusting the timing belt replacement warning system (Land Cruiser KZJ9#, HiLux Surf KZN18#, Land Cruiser HDJ10#)

1. Setting the display mode T-BELT (timing belt). a) Set the display mode “ODO/TRIP” (odometer/trip computer) to “ODO” mode and turn off the ignition. b) While holding the trip computer switch pressed, turn on the ignition for 5 seconds. c) Release the switch and press it again after 5 seconds. d) Switching the display to the “ТBELT” mode is accompanied by the display of data on the vehicle’s mileage at the time of the last belt replacement: – for example, in kilometers 15 (thousand) – in miles: 9 (thousand) Note: if the odometer was replaced before the belt was replaced, his testimony will not correspond to reality.

2. Setting a new mileage value at the time of belt replacement. a) To set a new mileage value, press the trip computer switch. Note: Pressing the switch once changes the mileage value by one. If the pause between pressing the switch reaches 30 seconds, the new mileage value will be recorded and the display will first switch to “ODO” mode and then to normal mode. b) After setting the required mileage, keep the switch pressed for 5 seconds. c) Make sure that the display switches to “ODO” mode and the belt replacement warning indicator goes off.