What to do if the Toyota Land Cruiser T-Belt light is on

Answer to a related question: How to reset a T-belt message? This information is available on the Internet, just in case I posted it in the form of a record.

For models before June 1999. You need to unscrew the screw from socket “0” at the rear of the instrument cluster and screw it into socket “10”. After the next 100,000 km, return the screw to slot “0”.

For models from June 1999. 1. Setting the T-BELT a) Set the ODO/TRIP (trip meter/trip computer) display mode to ODO mode and turn off the ignition. b) While holding the trip computer switch pressed, turn on the ignition for 5 seconds. c) Release the switch and press it again after 5 seconds. d) Switching the display to T-BELT is accompanied by the display of data on the vehicle's mileage at the time of the last belt replacement. Note: if the odometer was replaced before the belt was replaced, its readings will not correspond to reality. 2. Setting a new mileage value at the time of belt replacement. a) To set a new mileage value, press the trip computer switch. Note: pressing the switch once changes the mileage value by 1 thousand km. If the pause between pressing the switch reaches 30 seconds, the new mileage value will be recorded and the display will first switch to ODO mode and then to normal mode. b) After setting the required mileage, keep the switch pressed for 5 seconds. c) Check that the display has entered ODO mode and the belt replacement warning indicator has gone out.”

T belt how to extinguish

Resetting the T-Belt indicator

a) Set the display mode “ODO/TRIP” (trip meter/trip computer) to “ODO” mode and turn off the ignition. b) While holding the trip computer switch pressed, turn on the ignition for 5 seconds. c) Release the switch and press it again after 5 seconds. d) Switching the display to the “ТBELT” mode is accompanied by the display of data on the vehicle’s mileage at the time of the last belt replacement: – for example, in kilometers 15 (thousand) – in miles: 9 (thousand)

Note:

If the odometer was replaced before the belt was replaced, its readings will not be accurate.

In a number of Toyota Land Cruiser engines, the timing belt (gas distribution mechanism) synchronizes the crankshaft and camshaft. Land Cruisers are equipped by the manufacturer with a warning system about the approaching expiration date of a part. The Toyota Prado 90 t belt indicator on the dashboard lights up at 100,000 km.

What does T-Belt mean?

The timing belt is a consumable part of the engine with a limited service life. It must be changed, according to technical regulations, after a certain mileage or time period.

The vehicle manufacturer recommends changing the belt and roller every 100–150 thousand km during normal operation of the Land Cruiser. These values ​​are entered into the on-board computer program. When the mileage approaches the set number, the indicator on the instrument panel lights up.

The T Belt inscription notifies the car owner about the need to replace the timing belt.

Why change the timing belt

A design feature of some Land Cruiser engines is the dependence of the power unit on the timing belt. It synchronizes the operation of the gas distribution mechanism. A broken part can lead to serious engine damage. Valves and pistons fail. In severe cases, the engine is completely damaged.

In a number of engine models, if the belt breaks, the valves and pistons do not collide, but the car cannot start and move.

Reasons for replacing the timing belt:

• the part has reached the service life recommended by the manufacturer;
• replacement of faulty timing elements;
• visual inspection revealed external damage;
• weakened tension;
• when purchasing a used Toyota Land Cruiser.

Under severe operating conditions of the machine, the belt wears out after 50–60 thousand km, which must be taken into account.

If the car is used rarely, when the mileage is up to 100,000 km, the part needs to be changed every 4 years.

How do I turn off the T-Belt warning light?

The alert indicator lights up when the mileage approaches the preset mileage. After replacing the belt, you need to enter new data, and the light goes out.

If the old indicator is not reset or incorrect information is entered, the T-Belt icon will continue to light.

To reset the t belt on Toyota Land Cruiser 100 and Prado J90–120, you need to:

1. Turn on the ignition.
2. Move the speed and distance indicator to the ODO position - press the on-board computer switch (button) until the total mileage appears.
3. Turn off the ignition.
4. Keep the button pressed and simultaneously turn on the ignition for 5 seconds.
5. Release the button and turn off the ignition for 5 seconds.
6. Press and hold the switch again for 5 seconds. with simultaneous switching on of the ignition.
7. Release and after 1 sec. press the button again - a 2-digit number appears on the display.
8. Release the switch.
9. Apply short pressure to set the required distance. One unit is equal to 10,000 (10=100 thousand).
10. Press and hold the button for 5 seconds. A number with the total mileage will appear on the display.
11. Turn off and turn on the ignition.

As a result of the manipulations, the T-Belt indicator light will go out.

Perform zeroing with the engine turned off. It is necessary to strictly observe time intervals during the work process. The switch is located on the instrument panel.

How to reset a Toyota Land Cruiser Prado 150 t belt:

1. Turn on the ignition.
2. Switch the ODO display mode to TRIP B using the button.
3. Turn off the ignition.
4. Press and hold the TRIP switch.
5. Turn the ignition key to ACC position.
6. Hold the button until the data is updated.
7. Release the switch after 30 seconds. press again for 5 seconds.
8. Turn off and turn on the ignition.

The program reset the previous indicator. The mileage is automatically set to 150,000 km.

The t belt indicator on the Toyota Land Cruiser Prado 150 goes out.

In what cases does the Airbag safety light come on and possible reasons?

1. Pillow integrity problem. The module may stop receiving signals from: sensors, pillows, belts or other elements of this device. Perhaps the seat belt buckle is equipped with a “fastened” sensor, that is, when you are not buckled up and the metal rod is not installed in the buckle, the light will flash. What is it for? The fact is that the use of an airbag is justified only if you are buckled up, the airbag's firing speed is 200 km/h, and the impact of the airbag if you are not buckled up is equal to hitting a brick wall at a speed of 25 km/h. Taking this fact into account, automakers have programmed their Airbags in such a way that if you are not fastened, the airbag will not fire, in which case, as you understand, there is no need to talk about any safety. The “smart guys” who allegedly deceived the security system by pulling the belt behind the seat back or installing special “emulators” or decoys in the locks instead of belts are deceiving themselves; in the event of an accident, such “smart guys”, as well as their passengers, have no chance of survival.

1. Poor contact or complete absence of contact in the power supply wiring of the Airbag . Connectors are loose.
2. Shock sensors are faulty or damaged.
3. Moisture. If moisture gets on the belt buckle or contacts, or other important parts for which water is contraindicated.
4. The door contact is broken. When doors are changed or some repair work is performed and the connector is disconnected, when the power is turned on, the SRS/Airbag lamp will light up, because a malfunction has been detected by the system. To fix it, you need to reset the module memory.
5. Malfunctions of the control module itself. In this case, only replacement will help you.
6. Circuit breakers. Faulty fuses quite often cause the airbag indicator to light up, but the fuse is the last thing people think about, or not at all.
7. Replacing seats or dashboard. If the wires or terminals are damaged during replacement, problems with the light bulb may occur.
8. Mistakes made when replacing the steering wheel. A poor connection or damage to the power cord may cause the Airbag or SRS light to stay on continuously.
9. The light stays on after recovery. When airbags have been restored or replaced after they have deployed, the safety system can remember the old position through a log entry. The solution is to remove the error.
10. The pillow's service life has expired. As a rule, an Airbag is considered to be in good working order for 8-10 years, after which no one can guarantee safety.
11. The mains voltage is too low. In this case, check the battery and, if necessary, replace it in accordance with the sequence.

As you can see, there are many reasons why the Airbag light flashes or lights up . Determining the cause on your own is quite difficult and unsafe, since the slightest violation of the rules for diagnosing or replacing an airbag can lead to it simply not working in an emergency. Don’t take risks and entrust it to professionals, in which case you will have a guarantee that the work will be done efficiently, and your Airbag will not let you down in difficult times.

Are there differences in the reset process on different Toyota Land Cruiser models?

Some Land Cruiser models produced before 1999 have a mechanical odometer.

To reset the T Belt on a Toyota Prado 90, you need to tighten the screw on the electronic dashboard plate. There are 2 holes on the back of the panel in the upper right corner. One has a screw screwed in, the other is loose. The instrument panel is pre-disassembled.

Similar steps for resetting t-belt data on the Land Cruiser 80. A number of models have a hole on the dashboard with a plug, opposite which there is a reset button. Using a sharp long object (knitting needle, toothpick) you can press the mileage switch. The data is reset and the icon goes out until the next 100,000 km.

Toyota Land Cruiser 100, 200, left- and right-hand drive, are unified with Prado J120, J150 crossovers. They are equipped with identical electronic odometers. Therefore, the T Belt reset occurs according to the standard principle. Variations in the progress of work depend on the type of ODO and the version of the on-board computer.

Detailed information is contained in the vehicle operating instructions.

The T Belt light on Toyota Land Cruiser vehicles comes on when the timing belt is due for replacement. Previous mileage data is not automatically reset. You need to reset the information after each installation of a new belt. The procedure for resetting electronic odometers is almost the same. Changes in the progress of work depend on the series and year of manufacture of the car.

Reset t belt nissan

Step-by-step instructions - Resetting the T-Belt indicator: Set the speedometer mode to ODO and turn off the ignition. While holding the trip computer switch pressed, turn on the ignition for 5 seconds. Release the switch and press it again after 5 seconds. Switching the display to T-BELT mode is accompanied by the display of data on the vehicle's mileage at the time of the last belt replacement. Note: If the odometer was replaced before the belt was replaced, the odometer reading will not be accurate. We set a new value (mileage) to replace the timing belt. Set the display to whatever value you want.

The T-Belt light came on and the question arose: how to put it out, the belt was changed 40 thousand ago. I did the following: 1) Inserted the key, pressed the odometer button, without releasing it, turned on the ignition and kept the button pressed, released the button and turned off the ignition. 2) After 5 seconds - sleep So we exchanged tyrs! The T-Belt light came on and the question arose: how to put it out, the belt was changed 40 thousand ago. I did the following: 1) Inserted the key, pressed the odometer button, without releasing it, turned on the ignition and kept the button pressed, released the button and turned off the ignition. 2) After 5 seconds - pressed the button again and then turned on the ignition, holding it for the same seconds, then released it and after a second pressed the button again.

reset T-BELT valera Toyota Hiace after t km the T-BELT light is on, then I did it as expected. Reply to message. Re: reset T-BELT Pavel T-BELT means replacing the timing belt. To make the light go out you need to: Remove the rubber plug on the speedometer and press the button with a toothpick. Reply to message. on the forums Increasing ground clearance for Nissan Hell (3) Nissan power steering (1) Nissan does not go uphill Nissan Safari what to do (1) Nissan repair (1) Daihatsu electronics diagram (5) Mazda Toppo Bj Wide (1) Mitsubishi battery began to boil ( 14) Toyota Buying a car C.

How to reset T-BELT TOYOACE 97g?

Club of fans of minibuses and minivans Cars change, friends and forum remain And how to do it myself, I’ve also been trying to find the answer for a long time. Here's what else I can add on the high side. I also got to the digital instrument cluster, removed it, disassembled it, cleaned the dust and removed the deposits on the glass from the time of the king of peas, it’s also interestingly designed - concave mirrors, black velvet edging. The bell also turns on with a self-tapping screw. These are the observations, I took pictures, then I’ll post them somehow, I’ll go, I need to work. Last edited by admin on March 14, Apparently when they reset the E-belt, the speedometer was also caught.

He lies about a km from the real speed - he shows less. Nissan and Mazda clone AD-shki. There are two holes in the ignition switch next to the same light bulb, in one of them there is a screw. The book discusses the option of removing the panel with an analog panel, turning a certain screw from one socket to another, I understand that with a digital operation the operation should not be unnecessarily complicated, but how? Find your way around the ignition switch Added after 5 minutes 55 seconds: Any nerd who drives into a jeep becomes a decent mathematician. There are no holes where the bolt can be twisted.

Here is a photo of the dashboard, body of a Toyota Hiace 98. All messages 1 day 7 days 2 weeks 1 month 3 months 6 months 1 year Sorting field: Author Posting time Title Order: I used the old original speedometer, but now I have an optitron with a Grand High, I was moved with an electrician from a regular one to an optitron I already I think maybe something is not connected or connected incorrectly.

Please tell me how to enter the menu. On my Highland Granvia, I need to remove the dashboard. And move the jumper there. The white light will go out and the countdown to the next hundred will begin. Lights up constantly in orange until the time has come; when the ignition is turned on, it does not light up.

To turn it off, you need to remove the instrument panel, there is a microswitch on the back of the speedometer. But I didn’t do this myself, I changed the timing belt, remembered the mileage, and that’s it. Tell me how to change belts at home? After what mileage is this done, etc. I removed the radiator so as not to pierce the aluminum with all sorts of shells, and I wanted to find the marks. The air conditioner radiator has been gone for a long time and everything is immediately visible. The pulley was removed by lightly but persistently tapping with a hammer, alternately from above, where everyone has an air conditioning compressor, from below.

Everything else just fell into place. Secondly, many people do not light up, or rather, I have not heard that the indicator worked for anyone, if for someone it works, post a photo, it will be interesting.

“Airbag SRS” lights up - causes and solutions

Airbag SRS ”, “Airbag”, or “ SRS indicator light is on ; not everyone knows the answer to this question. It is this alarm signal that will be discussed in our article today.

Contrary to the prevailing stereotype, airbags are not just one airbag that flies out of the steering wheel in the event of an accident or accident. A modern Airbag is a whole system that includes a lot of sensors, airbags: driver, passenger, and rear-row passengers, and protection can be not only frontal, but also lateral. The airbags work in close contact with: the control unit, pretensioners, belts, squibs, shock sensors and more. We will not delve into the theory and go away from the topic; for those who want to learn more about airbags, I advise you to read this article. Today we will talk about exactly why the Airbag indicator is on and what it means.

The first thing that comes to mind when you see a red light with the word Airbag is that something is broken. In short, in most cases this is the case; this light does not light up if everything is in order in the security system, with the exception of a short-term light up when starting the engine. However, there is no reason to throw a tantrum and become depressed. Like all car breakdowns, this one can be repaired.

It is important to understand that when “SRS or Airbag” is on, this does not mean that the reason lies precisely in the airbag, as we said above. The Airbag is a whole system that includes a lot of different devices, so if the Airbag indicator lights up, it is necessary to perform a comprehensive check.

In good condition, the light comes on after turning the key to the “ON” position, and the module performs a self-test of the functionality of the entire system. When the Airbag/SRS light is checked, it may start flashing (about 6 times). If no faults are detected, the airbag light should stop lighting, at least until the next time the engine is started. If malfunctions are still detected, the SRS/Airbag indicator will continue to light.