Installing a car alarm on a Toyota Corolla

3370 Apr 20

These days, alarms are much more than just a means of remotely opening and closing locks. Using these systems, you can start the engine from the key fob, warm up the interior remotely, and many more convenient functions are available. Such multifunctional security systems are much more difficult to install, so before you buy a car alarm, decide for what purpose it is needed and whether you can install it.

Let's consider installing a security system with auto start on a 2008 Toyota Corolla with a manual transmission. For cars with automatic and robotic transmissions, this instruction is not suitable.

Car alarm connection points for Toyota Corolla 2E 1990

ChainColorPolarityLocation12 V constant white positive wiring harness from the ignition switch 12 V constant black/red starter black/white ignition black/orange ignition 2 black/yellow ACC blue/red turn signals green/black green/yellow wiring harness in the steering column or in the sill door switch wire red/white negative in the door stop pillar - signalgreen/whitepositive wiring harness in trunk thresholdred/whitenegative trunk light

Ignition system

We connect the security system to the ignition switch. We find the ignition - it is a white wire. It must be broken and connected to the first end coming from the ignition switch (the thin yellow wire of the car alarm), and to the second remaining part of the wire we connect the thick brown wire of the purchased security system.

In order to connect the interlock circuit, you need to use the relay that comes with the security system. We connect its first wire to the wire of the main module of the system being installed, and the second to the positive ignition wire. It can be found using a control light: it should be in contact with the wire and light up when the ignition is turned on.

To install autostart, you need to bypass the immobilizer installed in the car. To do this, take the battery out of the chip key and place it in the autostart module that comes with the car alarm.

Now you need to connect the Start/Stop button. We take the red wire coming from it and connect it to the negative output from the starter. This will create a simulated button press for remote start.

Next, to monitor the engine, we will connect the yellow car alarm wire to the generator (the pink wire coming from it).

Car alarm connection points for Toyota Corolla 1998

ChainColorPolarityLocation+h/red and whitePositive ignition switchignitionh/orignition 2h/whiteACCgoal/krstarterkrgasoline pump/wthreshold water-limit door cr/whiteNegative dimensionsgreenPositive block pred.z.s.s.s./w and sin/bNegative sidewall water-la blue r-m

Car alarm connection points for Toyota Corolla 1998

ChainPolarityConnection+12BPositiveMust be connected to the 4mm2 white wire coming from the 6-wire white connector on the fuse block.Turn IndicatorsTo control the turn indicators, you must connect to the black/green/silver dot wire at position #9 and the green/yellow/silver dot wire at position No. 3 on the 6-wire white connector located under the fuse box on the bottom of the pillar on the driver's side.Power windows: Driver's door windowPositive impulseTo close the driver's door window, cut the yellow 1.5 mm2 wire and make the appropriate connections.Power windows: Passenger's door windowFor When closing the passenger door window, cut the green-red wire with a cross-section of 1.5 mm2 and make the appropriate connections. The connection for the driver's door window is made directly inside the driver's door, and for the passenger's door window in the harness coming out of the driver's door. Engine blocking: Fuel pump Positive To block the fuel pump, cut blue-black with silver dot 1.5 mm2 wire at position #3 in the harness coming from the 11-wire white connector located near the bottom of the driver's side pillar and make the appropriate connections. Hood limit switch negative Install an additional switch on the decorative grille, in which the car's headlights are installed, next to the left headlight. Door and trunk limit switchMust be connected to the red-white with a silver dot wire with a cross-section of 1 mm2 at position No. 11 in the harness of the 6-wire white connector located at the bottom of the "A-pillar" side driver. Central locking: Negative pulse To lock and unlock the doors, you must connect to the blue-white with a silver dot locking wire in position No. 6 and to the blue-red and silver dot unlocking wire in position No. 1 in the wiring harness coming from the standard central locking unit , mounted directly on the side panel of the fuse box. Alarm Siren Location Place the siren (monoblock alarm) in the engine compartment on the side panel of the fender on the left side near the air filter.

Final stages

To install the antenna module, you simply need to connect the connector coming from it to the main module of the security complex (the connection port is indicated in the instructions). The same is done with the shock sensor.

It is very important to place this device on a horizontal plane! Because in other planes it will come off over time.

To connect the siren, we draw a wire coming from the connector of the car alarm itself and connect it to the scarlet wire of the siren. We connect the second remaining black one to the car body.

After these operations, you can program the security system unit and check whether it is compatible with your car. To do this, you need to connect your laptop via a USB cable to the main alarm module. You need to download the necessary application to your laptop, depending on the system manufacturer. In this application, you need to enter the make and model of the car, and then click the “Load settings” button.

Car alarm connection points for Toyota Corolla 1998 - 1999

ignition black with yellow in the harness from the lock starter red or black in the harness from the lock dimensions green (+) on the driver's side in the white connector under the fuse block turns green with black, green with yellow low beam red with white (-) on the steering column tachometer blue with white in the front connector on the distributor door limit switch red with white (-) in the white connector on the driver's side behind the fuse block trunk limit red and white on the trunk light central locking Negative control Locking - blue with black (green with yellow) Unlocking - blue with yellow (blue with red) on the driver's side behind the fuse block in the white connector above brown connectors brake lights green and white on the frog window lifters Reverse remaining on ground Lifting the left front window: blue with red; Right front window lift: blue and white; Left rear window lift: Right rear window lift: blue with black; on control buttons

Car alarm connection points for Toyota Corolla

Electrical wiring for Toyota Corolla 2E 1990

Chain	Color	Polarity	Location
12 V DC	white	positive	ignition switch wiring harness
12 V DC	black red	positive	ignition switch wiring harness
starter	black White	positive	ignition switch wiring harness
ignition	black/orange	positive	wiring harness from the ignition switch, a break in this wire stops the engine
ignition 2	black/yellow	positive	ignition switch wiring harness
ACC	blue red	positive	ignition switch wiring harness
direction indicators	green/black green/yellow	positive	wiring harness in steering column or sill
door switch wire	Red White	negative	in the door pillar
stop signal	green/white	positive	wiring harness in threshold
trunk	Red White	negative	trunk light

Electrical wiring of Toyota Corolla 1998

Chain	Polarity	Connection
+12B	Positive	You need to connect to the 4mm2 white wire coming from the 6-wire white connector on the fuse block.
ignition	Positive	b/or - ignition switch
ignition 2	Positive	black/white — ignition switch
ACC	Positive	goal/cr — ignition switch
starter	Positive	kr - ignition switch
Direction indicators	Positive	To control the turn signals, you must connect to the black/green/silver dot wire at position #9 and the green/yellow/silver dot wire at position #3 on the 6-wire white connector located under the fuse box on the bottom of the driver's side pillar.
Power windows: Driver's door window	Positive impulse	To close the driver's door window, cut the yellow wire with a cross-section of 1.5 mm2 and make the appropriate connections.
Power windows: Passenger door window	Positive impulse	To close the passenger door window, cut the green-red wire with a cross-section of 1.5 mm2 and make the appropriate connections. The connection for the driver's door window is made directly inside the driver's door, and for the passenger's door window in the harness coming out of the driver's door.
Engine Lock: Fuel Pump	Positive	To lock out the fuel pump, cut the blue/black/silver dot 1.5mm2 wire at position #3 in the harness coming from the 11-wire white connector located near the bottom of the driver's side pillar and make the appropriate connections.
Hood limit switch	negative	Install an additional switch on the decorative grille in which the car's headlights are installed, next to the left headlight.
Door and trunk limit switch	negative	Connect to the red/white/silver dot 1mm2 wire at position #11 in the 6-wire white connector harness located at the bottom of the A-pillar on the driver's side.
Central locking:	Negative impulse	To lock and unlock the doors, you must connect to the blue-white with a silver dot lock wire in position No. 6 and the blue-red and silver dot unlock wire in position No. 1 in the wiring harness coming from the standard central locking unit mounted directly on the side panel fuse box.
Alarm siren placement	Place the siren (monoblock alarm) in the engine compartment on the side panel of the wing on the left side near the air filter.

Electrical wiring of a Toyota Corolla 1998 - 1999

ignition	black with yellow in the harness from the lock
starter	red or black in the harness from the lock
dimensions	green (+) on the driver's side in the white connector under the fuse block
turns	green with black, green with yellow
low beam	red with white (-) on the steering column
tachometer	blue and white in the front connector on the distributor
door switch	red with white (-) in the white connector on the driver's side behind the fuse box
trunk limit switch	red and white on trunk light
central locking	Negative control Locking - blue with black (green with yellow) Unlocking - blue with yellow (blue with red) on the driver's side behind the fuse block in the white connector above the brown connectors
brake lights	green and white on a frog
window lifters	Reverse remaining on ground Lifting left front window: blue with red; Right front window lift: blue and white; Left rear window lift: Right rear window lift: blue with black; on control buttons

Electrical wiring of Toyota Corolla 2003

Chain	Color	Polarity	Location
+12	black\red	Positive	at the fuse box
ignition	black\white	Positive	at the fuse box
starter	red	Positive	at the fuse box
turns	green\yellow,green\black	Positive	at the threshold of the waters.
doors	red\white, red\yellow	Negative	at the threshold of the waters.
c.z.	blue\yellow-open, blue\white-closed	Negative	under the kick panel.

Electrical wiring of Toyota Corolla 2007

Chain	Color	Polarity	Location
+	white thick medium	Positive	egnition lock
starter	white thick extreme	Positive	egnition lock
starter 2	white thin opposite gray	Positive	egnition lock
ignition	grey	Positive	egnition lock
ignition 2	white thin opposite white thick	Positive	egnition lock
acc	black	Positive	egnition lock
c.z.	syn and f next to each other	Negative	from the door water-la white r-m
turns	goal and	Positive	water threshold
water conc	white	Negative	water threshold
end left rear door	Goal	Negative	water threshold
end rear door	light green	Negative	water threshold
end lane right door	brown	Negative	pass-ra threshold
end rear right door	St. green	Negative	pass-ra threshold
gasoline pump	light green thick	Positive	water threshold
charger	and	Positive	area behind the instrument panel (middle of 3)
stop	blue	Positive	frog or water threshold
ATTENTION!!! When connecting a remote start, both starters must be connected.

Electrical wiring of Toyota Corolla 2010

Chain	Color	Polarity	Location
brake	blue	positive	brake pedal, or second from the top from the left in the fuse block
pulse	separate wire	diagnostic connector in front of the fuse box
driver's door switch	white	negative	fuse box, top left connector
trunk limit switch	light green	negative	fuse box, top left connector
rear left door switch	blue	negative	driver threshold
turns	blue and yellow	positive	fuse box, top left connector
rear right door switch	light green	negative	right threshold
front right door switch	brown	negative	right threshold
when starting autostart, apply plus to the clutch pedal connector (can be done from the starter)

ATTENTION! Wire colors and locations may differ from those shown above. This information is advisory in nature and requires mandatory verification !

Car alarm connection points for Toyota Corolla 2003

ChainColorPolarityLocation+12 black\red.Positive at the fuse block ignition black\white.starterred turnsgreen\yellow, green\black in the water door threshold red.\white, red\yellow Negative central blue\yellow - open, blue/white — closed under the kick panel of water.

Car alarm connection points for Toyota Corolla 2006 (E130), right-hand drive, no immobilizer

Ignition switch: +12 – black/red ign1 – black/white ign2 – green ACC – green starter – red
Instrument panel, right connector: driver’s limit switch – blue on the edge, other doors’ limit switch – blue opposite

Instrument panel, connector on the left: turn signals - two white ones next to each other in the middle of the connector

Central locking : pull the driver's door to the button module - blue/yellow and blue/white thin

Brake – green/white on the frog

Trunk – on the button in the trunk red/white

Tachometer – on the injector (any non-black/white wire)

The hood end is your own.

Car alarm connection points for Toyota Corolla, Auris 2007

ChainColorPolarityLocation+ white thick middle Positive ignition switch starter white thick outer starter 2 white thin opposite gray ignition gray ignition 2 white thin opposite white thick acc black c. z. sin and f next to each other Negative of the door water-la white r-m-turns head and g Positive threshold water-la-konts water dvwhite Negative end left rear two head end rear two light green end per pr dvkorichthreshold pass -rear end of engine green benzene sucking lime thick Positive water threshold charging oil behind the instrument panel (middle of 3) stopspin frog or water thresholdATTENTION!!! When connecting a remote start, both starters must be connected.

Car alarm connection points for Toyota Corolla 2008 Left-hand drive, manual transmission

ChainColorPolarityLocation+ 12V White thick Positive Ignition switch ACC Black thin IGN_1 Gray IGN_2 White thin To avoid simulating pressing the clutch pedal, the starter can be connected like this: Starter Blue thick Positive On the block with the relays, behind the climate unit, under the radio Fuel pump Green thick In the harness to the upper left connector of the fuse box Bug raker Green thin Negative Left front door end White thin Left rear door end Blue thin Lower left connector behind the panel at the driver's left foot. Or the top connector at the back of the fuse box (It’s not convenient to connect there, you need to remove the entire fuse box, for the sake of just one wiring, it’s lazy...;) Right front door end Brown thin Harness above the glove compartment Right rear door end Green thin Turns Blue/red Positive In the harness to the large connector on the fuse block, connector on the left , top, second Yellow Tachometer Gray Pulses Harness to the diagnostic connector Central locking Yellow - open Blue - close Negative Harness from the driver's door, white connector Handbrake Black Right upper connector of the fuse box Lineman fits Saturn AU-50. You can hide the entire key there, but I only took out the chip from the key, and it was used by the crawler. Shredded the third spare key, which does not have central locking control buttons. The outer shell is rubber and can be cut off with a knife. There is a plastic case inside and you can see the chip there; it is pulled out.

The Toyota interior is well versed. Remove the entire top cover of the torpedo. Everything is held there by clips and three screws. And you need to remove the left and right pillar trims.

And unscrew the airbag, this is done by removing the glove compartment, looking for two 12 bolts at the top, and unscrewing it with the head through the extension. We disconnect the pillow - the yellow connector.

When starting up, the system will complain that the airbag is faulty, no problem; when you connect the airbag, this error will disappear on its own.

We hide the signaling and lineman blocks behind the air duct in the middle, spreading them out with a piece of foam rubber.

Toyota Corolla 180 model from 2014 Alarm installation

Connection points for Toyota Corolla 2014 automatic transmission or manual transmission

Installing StarLine A93 CAN LIN with engine start

1. Remove the driver's door sill trim (fastened with latches) and the plastic trim of the left kick panel (fastened with latches and a clip). Unscrew the two screws securing the pedal assembly cover and remove it. Then remove the decorative trim to the left of the steering column (fastened with snaps).

2. Remove the instrument panel. To do this, you need to remove the decorative trim and the air duct to the left of the instrument panel (fastened with snaps). Then remove the decorative trim of the central air duct and the decorative frame of the radio (fastened with snaps). Next, remove the decorative frame of the instrument panel (fastened with latches), unscrew the two screws securing the instrument panel and remove it, disconnecting the connectors

3. To access the ignition switch connector, remove the steering shaft housing. To do this, you need to unscrew the two fastening screws and remove it

4. Install the antenna module with built-in shock and tilt sensor on the windshield, LED on the left pillar. Install the service button covertly in any convenient place

5. Install a siren under the hood (attach it to a standard nut), an engine temperature sensor (using plastic ties) and a limit switch. Route the wires to the passenger compartment through the standard seal in the center of the engine shield

6. Attach the central unit of the StarLine security and telematics complex to the instrument panel

7. Connect the mass of the StarLine security and telematics complex in the left kick panel to the standard location

8. Connect the CAN bus of the StarLine security and telematics complex in the diagnostic connector harness (OBD 2)

9. Connect the engine starting power circuits in the ignition switch connector harness. It is recommended to make these connections by soldering

10. On a Toyota Corolla with a manual transmission, connect an imitation of pressing the clutch pedal in the clutch pedal connector harness

11. To bypass the standard immobilizer, remove the battery from the key and place the key in the StarLine BP-03 immobilizer bypass module. Then place the VR-03 bypass module antenna on the standard antenna located on the ignition switch

12. Connect the power supply of the security-telematics complex and the power autostart module to the mounting fuse block. It is recommended to make these connections by soldering.

Car alarm connection points for Toyota Corolla 2010 manual transmission

ChainColorPolarityLocation+ 12 Volt white thick positive ignition switch ignition gray ignition 2 white thin acc black starter white thick extreme and white thin brake blue brake pedal, or second from the top from the left in the fuse block pulse separate wire diagnostic connector in front of the fuse block driver's door end white negative fuse box, top left connector trunk end light green fuse block guards, upper left connector rear left door end blue driver's threshold turns blue and yellow positive fuse box, top left connector rear right door tip lime green negative right threshold, or top right large connector in the fuse block front right door tip brown right threshold, or top right large connector in the fuel pump fuse block lime green positive driver's threshold central locking close - blue, open - yellow negative in the driver's feet top right connector when autostarting, apply the clutch pedal connector plus ( maybe from the starter)

Alarm connection points in Toyota

The function of the anti-theft system is to protect the vehicle from theft. Connection points are “signaling” sensors installed in the car. They detect external influences (impacts, body tilts, movement) and react to manipulations in the cabin.

Alarm connection points for Toyota Prado 120:

Ignition - No. 1 black/red, No. 2 blue/yellow on the ignition switch. Polarity is positive (+).
Starter - black/white on the ignition switch (+).
Turns - No. 1 black/blue, No. 2 yellow/blue in the left plexus (+).
Dimensions - green in the left plexus (+).
Engine blocking - in gasoline engines, under the hood in the harness for the injectors, black/red.
The door switch is red/yellow for the driver and front passenger doors. Pink/black for rear left. Pink/blue - rear right. Polarity is negative (-). Location in the rapids.
Luggage limit switch - red/blue (-) in the left sill.
The brake light is yellow/green in the left threshold.
The key in the lock is yellow/green, negative.
ACC - white/black in the ignition switch.

On Prado 120 2006–2008, the door and trunk switches are located in the fuse box, middle side connector. Turns, dimensions - upper left fuse box connector.

Central locking:

closure - black/orange, lower left connector behind the fuse box;
opening - green, at the bottom of the block there is a connector near the brake pedal.

In 2009 cars, the central locking - blue (closed), green (open) - is located in the driver's door.

Alarm connection points for Toyota Land Cruiser 100:

In the ignition switch. Ignition No. 1 black/red for anti-theft system with transponder key, ignition No. 2 black/blue, circuit +12V red/black, red/white. (+). Disabling the standard alarm - red/black.
In the fuse box. End caps green/white in the braid attached to the top right (-). Central locking - blue/white to close, black/green to open (-). Brake light green/white (+). Klaxon green/orange (-) in the right harness of the box. Parking signals - green, in the controller.
Behind the glove compartment. Tachometer – black wire, alternating polarity.
Turns relay. Turn signals – green/yellow, green/black. (+). The harness is located to the left of the steering column.

On Toyota Land Cruiser, connection points and wire colors may vary. The transformation depends on the generation, series, and year of manufacture of the model.

Full details can be found in the operating instructions.

Car alarm connection points for Toyota Corolla 2014

ChainColorPolarityLocation+ 12VBluePositiveAbove the steering column (Power supply for power steering)ASS BlackIgnition switchIGN1GrayIGN2GreenAutomatic transmission starterWhiteManual transmission starterGreenOn the clutch pedal frog (you can immediately block the starter)TachometerGrayImpulsOn the diagnostic connector or on the gray connector above the steering columnCentral lockingC niy - locking Yellow - unlocking Negative Harness from the driver's door Left front door end WhiteLeft threshold (Some wires on colors are repeated, you need to call) Left rear door end Blue Trunk end Light green Handbrake Black Trunk opening (Power) Pink (thin) Positive Turns Blue Yellow Right front door end Brown (or purple) Negative Right threshold or in a plastic box above the radio where the wiring harness goes. There are many identical wires of the same color in the harness, so you need to call. (In the same place, in a plastic box, you can place a homemade immobilizer bypasser with a chip. 15 turns on the chip and the lock). Right rear door limit Green (or light green) Locking Gray Positive White connector above the steering column As on all Toyota Corollas and similar Toyotas, the upper one is removed the dashboard cover, and there is access to everything.

Car alarm connection points for Toyota Corolla Axio Hybrid, PTS, 2014

By can Pandora DX9X (car model code 2121) sees doors, trunk, ignition, brake pedal, parking, fuel in liters, mileage.
Controls via can the emergency lights, central locking (if installed on staff, the central locking will not open when Pandora is disarmed), unlocking the trunk, and raising the windows. Slave mode and launch from the standard key fob are possible. You can connect to can on the dashboard: twisted pair green (can-h) and white (can-l).

Bypassing the standard immobilizer using the Toyota can rx-tx protocol.

To start, you need to connect to the rx, tx and slp wires.

RX and TX can be found in the standard 6-pin connector (which only has 2 pins), attached to the standard wiring on the left behind the glove compartment. RX – black, TX – red.

SLP – pink in the steering shaft lock connector (pin 4).

I checked the running engine by voltage.

Installation

The first step is to remove the plastic panels of the car interior. The operation is very easy due to the fact that the plastic in this machine is flexible. You need to remove it with a long, flat object.

Do not dismantle the plastic with a screwdriver, as this may damage it!

After this, for installation it is necessary to find connection points to the standard vehicle wiring. In Toyota Corolla, their role is played by the Can-bus and the ignition switch. The connection points for this bus can be found behind the dashboard - these are light green and light green-white wires, which are twisted together in pairs. We connect the control wires of the security system to them (they are indicated in the instructions).

The power supply for the car alarm is located in the same place as the Can-bus wires (blue thick wire), we attach the plus of the security system to it. A wire with black and white insulation comes out of the same chip; we connect the minus to it.

It is much better to solder wire connections than to twist them. If the contacts are made of different materials, then over time they may oxidize and the alarm will stop working.

It is necessary to ensure that the system responds to the condition of the rings. You should connect the wires of the alarm itself to the contacts of the switching socket, from which the green and brown wires come out (the map of their connections is in the instructions for the car alarm).

Now let's connect the trunk ring. In order for it to react, it is necessary to connect the wire coming from the security system unit to the white wire of the driver's threshold.