Replacing windshield wiper blades: how to remove and replace front and rear wipers (video)

Rav 4 wipers are an element of the windshield (and rear) glass cleaning system that provides the necessary visibility of the road. Consumables must reliably clean constantly dirty glass and not wear out quickly. The size of the brushes of different generations changed, with the rear element and the front passenger one becoming smaller over time, and the part on the driver’s side, on the contrary, became longer (on the latest generation - 650 mm). Below we will talk about the types of wipers, manufacturers and nuances of replacing this accessory on a Toyota Rav 4 car.

Checking the condition, adjusting and replacing windshield wiper blades

PROCEDURE 1. Road film accumulates on windshield wiper blades over time, reducing their efficiency, so the blades should be washed regularly in a mild cleaning solution. Checking the condition of the blades and the initial position of the wiper arm 2. Windshield wiper assemblies with brushes should be inspected regularly.
If inspection reveals hardening or cracks in the rubber of the brushes, replace the brushes. If nothing unusual is found upon inspection, wet the windshield, turn on the windshield wipers, let them run for a while, and then turn them off. An uneven brush mark on the glass or streaks on clean glass indicate that the brushes need to be replaced. 3. If the brushes do not clean the windshield well enough, then the following reasons are possible. – When the car went through an automatic car wash, wax particles got on the windshield. These particles can be removed by adding a detergent that has wax-dissolving properties to the windshield washer fluid. – Filling the reservoir with windshield cleaning fluid with solvent-resolving properties can significantly improve the performance of the windshield wipers. Grease-dissolving cleaners cannot completely clean glass. – Damage to the brushes can also cause poor glass cleaning; the brushes should be replaced. – The installation angle of the windshield wiper arms is not as required. 4. During operation of the windshield wiper mechanism, the fastening nuts may become loose, so they should be checked and, if necessary, tightened each time the blades are checked . Check 5. Turn the windshield wipers on and off until they return to their original position. Windshield: Check the distance between the blades and the lower edge of the windshield with the windshield wiper off. The distance should be on the driver's side a = 15 - 25 mm, on the front passenger's side b = 17 - 27 mm. Markings -1- are located in these places. Rear window: When the windshield wiper is off, the blade should lie horizontally at the upper edge of the wiper stop plane. Check angle of the windshield wiper arm ATTENTION Checking the angle of the windshield wiper arm must be done when the glass cleaning efficiency is low or when there is noise when the blades operate.

6. Turn the windshield wipers on and off until the wiper arms return to their original position. Remove the windshield wiper blades.

7. Insert windshield wiper lever 1 into tool HAZET 4851–1 or AUDI 3358 and secure with a bolt. Checking and adjusting the angle of the wiper arm^ 1 wrench 2 wiper arm 3 tool AUDI 3358

If adjustment is necessary, being careful, use a wrench 1 to turn the AUDI 3358 tool until the arrow appears on the scale at the required value of ±2°. Nominal values ​​of the windshield wiper arm angles. Driver side: –9° Passenger side –3° Rear wiper: 0 – 2° 9

Remove tool AUDI 3358, install and secure the windshield wiper blades. 10. Install the blade and check the operation of the windshield wiper.

The latest generation of Toyota RAV 4 is the CA40 generation, which is characterized by changes in the structural features of the body and power unit. Windshield wipers for the latest version of RAV 4 are identical to the previous generation, and are also completely interchangeable with the restyling and pre-restyling versions.

Original articles

A genuine set of windshield wipers is the best option for replacement, as it fully takes into account the structural features of the vehicle body. The average cost of stock wipers varies between 800-1300 rubles per set, official articles - 3397010297, 3397013434, 3397010RR.

Replacement options

Analogues of original components are often purchased in order to save on vehicle maintenance - often such parts have a level of quality that is not inferior to the original ones, but have a lower cost, which is characterized by the absence of overpayment for the brand.

The most popular alternative windshield wipers are the following models:

Frame

Frame wipers are a two-component structure consisting of a metal frame and a removable brush. Characterized by low cost and low maintenance. A popular model for RAV 4 is SWF VisioNext, article number 119860.

Frameless

The main feature of frameless wipers is their aerodynamic design, which ensures low noise levels and tight fit. A popular model is Valeo Silencio, article number 567947.

Hybrid

The design of hybrid windshield wipers combines all the advantages of frame and frameless types - wipers are characterized by high efficiency and a long service life, but have a high cost on the market. The most popular options for Toyota RAV 4 are Trico Hybrid, part numbers hf480 and hf485.

Winter

A specialized type of windshield wipers designed for use in cold weather. Resistant to temperature changes and prevents the risk of glass deformation if there is a crust of ice on its surface. The Bosch “AR601S” is considered a proven option.

Replacement

Installing a new set of windshield wipers on the latest generation RAV 4 will not cause any particular difficulties even if you do not have practical skills in servicing the car - the entire process is carried out according to an intuitive scenario and takes no more than 20 minutes. To replace the windshield wipers, you will need a slotted screwdriver or pliers, as well as a piece of foam rubber or a small cloth for cushioning. Replacement occurs as follows:

• To begin, move the metal frame of the windshield wipers away from the windshield and place a small soft cloth: a towel, foam rubber or rags for wiping. The fact is that the degree of pressing to the surface of the windshield is determined by a mechanism with a spring, which can work when servicing the windshield wipers and deform the glass;
• Next, using a screwdriver or pliers, unclip the latch that secures the wiper blade to the frame and pull out the worn part by moving it upwards and towards you. The “hook” type fastening itself is located on the back side of the windshield wipers at the bottom of the blade;
• Then we carefully lubricate the frame seats with technical lubricant, which will prevent metal corrosion, and install new brushes, after which we fix the new elements. We repeat a similar procedure with the second wiper.

The rear wiper is changed in the same way, but the clips are removed from the inside of the trunk door after first releasing the decorative plug.

Choosing windshield wiper blades for Toyota Rav 4

Rav 4 wipers are an element of the windshield (and rear) glass cleaning system that provides the necessary visibility of the road. Consumables must reliably clean constantly dirty glass and not wear out quickly. The size of the brushes of different generations changed, with the rear element and the front passenger one becoming smaller over time, and the part on the driver’s side, on the contrary, became longer (on the latest generation - 650 mm). Below we will talk about the types of wipers, manufacturers and nuances of replacing this accessory on a Toyota Rav 4 car.

Why Toyota Dubrovka?

Our clients are spared the need to waste time searching for original items, risking overpaying or buying a fake. Everything you need can be purchased from us, receiving a high-quality product at a price below the dealer price.

Our technicians and diagnosticians have been certified by the manufacturer and have many years of experience. They have successfully repaired hundreds of cars of this brand and have consistently received positive reviews. You can sign up for maintenance by filling out and submitting the form online or by calling us.

Dimensions of Rav 4 twins

Frame

1. What types of windshield wiper blades are there?
2. Frame
3. Frameless wipers
4. Hybrid
5. Good producers
6. Changing wipers on Toyota Rav 4 3
7. Conclusion
8. Video

What types of windshield wiper blades are there?

The following types of windshield wiper blades can be installed on Japanese Toyota Rav 4 crossovers:

• frame;
• frameless;
• hybrid.

Each type has advantages and disadvantages.

Frame

The classic option for a car is a frame one. The design is rigid and guarantees a tight fit of the blade to the windshield. The price of frame wipers for Rav 4 is low; for reasons of improving aerodynamics, some of them are equipped with a spoiler. The downside of the frame structure is its fragility. With use, the parts become loose, which leads to a loose fit between the rubber and the glass. The quality of cleaning suffers from this. In winter heavily to the structure and ice forms.

Components of frame wipers

Frameless wipers

The body of the frameless brushes is made of rubber and plastic, and the glass cleaning strip is fixed inside. The advantage of this design will be resistance to warping and icing , and good aerodynamics . The brush fits tightly onto the windshield. Replacement of worn-out blades is carried out without installing a new housing. As a result, this type of brushes for Rav 4 belongs to the all-season class.

Components of frameless

A design flaw manifests itself when installed on some car models - without installing an additional adapter, fastening is impossible. A number of manufacturers provide windshield wipers with adapters, but installation difficulties may arise.

Hybrid

Hybrid is a universal type that combines the advantages of other designs. Hybrid windshield wipers for Rav 4 are structurally strengthened , without affecting aerodynamics. The frame is small and it is tightly covered with a plastic cover. severe frosting in winter , and the quality of glass cleaning remains high (due to the tight fit of the wipers). The brushes are universal and can be installed on any car. The downside is the high price . But it is justified by long-term high-quality work and suitability for all seasons.

Hybrid design

When do brushes need to be replaced?

Everyone knows what “wipers” are - this is a special device in the form of a lever and a brush for cleaning the windshield and sometimes the rear window. They can be framed or frameless. In the first option, these are moving parts that hold the cleaning surface on the wind window.

Glass cleaning mechanism

Unfortunately, this species is quite delicate because it is vulnerable to snow and rain, which eventually turns into ice and damages the frame surface. In addition, the cleaning part does not fit tightly to the surface, and therefore does not clean well enough.

The second option is more convenient, because instead of a “rocker arm,” frameless ones have a spring that exerts pressure and presses the part against the windshield. Since they are made of rubber, they wear out quickly. Therefore, time is one of the reasons why there is a need for dismantling. A sign of failure is streaks on the windshield or rear window. This means that the wipers do not perform their functions.

Of course, dismantling the cleaning devices themselves is only a tiny part of the job. After all, windshield wipers are a large mechanism consisting of different parts. But they, of course, can be dismantled quite often, because they are consumables. You can find out how to change windshield wiper blades below.

Good producers

Glass cleaners for Rav 4 crossovers are supplied to the market by both Russian and foreign manufacturers. The choice of windshield wiper blades is wide, but it is better to buy products from well-known companies: Bosch, Trico, Valeo, Denso and Champion.

Bosch products are reliable and durable. The manufacturer has established itself as the creator of a high-quality and high-tech product, and automotive consumables are not the only segment of the group of companies’ activities.

Trico is a company with history that began producing windshield wipers at the beginning of the last century. Today the brand is considered one of the best car accessories on the market.

Valeo is a concern that supplies components for automobiles to the largest automakers. Valeo wipers are reliable and constantly improved.

The Japanese manufacturer Denso is working on the creation of automotive components; the production of windshield wipers is one of the company’s directions. As a supplier of automotive consumables, Denso ranks second in the global ranking.

Denso has been a long-time supplier of brushes for Toyota.

The American brand Champion focuses on the production of spare parts. The product range has recently been expanded to include windshield wipers for cars and trucks.

Wipers for Toyota Rav 4 are supplied by all of these companies. Which one to choose, everyone decides for himself.

Changing wipers on Toyota Rav 4 3

How to change worn windshield wiper blades? On the third generation Rav 4 crossover, windshield wipers are replaced in the following order:

1. The latch holding the brush is pulled up . To do this, it is better to use a screwdriver to avoid damaging your nails.
2. The leash is raised, the wiper is retracted.
3. The brush carefully removed . You need to release the leash smoothly, because if you pull back sharply, it can break the windshield.
4. The new brush is removed from the packaging and replaced with the old one . The latch snaps into place .
5. The procedure is repeated with the second wiper.

The Rav 4 has a hook type of attachment.

Original wipers Rav 4 3 can be ordered online. The part number for the passenger side wiper is 85212-42120. Its length is 405 mm. The article number for purchasing consumables on the driver’s side is 85222-42110. Its size is larger - 610 mm.

How to remove wipers from a 2021 Toyota Rav4

To install new front brushes, follow these simple instructions:

1. Fold out the latch on the body, then carefully insert the element into the slot and pull it until it stops. The easiest way to navigate is by the latch - if it snaps into place, the wiper is positioned as it should.
2. If you decide to change only the rubber bands, which allows you to save money, then several more steps will be added. After removing the element, inspect it and find the retainer that holds the elastic. It is located on the edge of one of the sides.
3. Grasp the elastic band and pull it out of place towards the lock. After it moves, simply pull the element out of the groove.
4. Remove the metal guides from the elastic; they are located on both sides and can be easily removed. Please note that there are cutouts in the plates on the side where the clamp is located.
5. Take a new elastic band and determine which side it has an ebb on. It is located where the latch is located. Insert the steel guides into place. To do this, carefully tuck them into the groove along the entire length.
6. Start inserting the rubber band with metal plates into the wiper body from the retainer side. Everything is simple, the main thing is to get into the grooves located every 10 cm. At the end, just gently press the end so that the elastic snaps into place.
7. The element on the rear brush changes in a similar way. It is important to ensure the accuracy of the alignment of the parts so as not to deform them and damage the rubber part.

Signs that the brush or rubber part needs to be replaced: the glass is not cleaned well, lines or stains remain on the surface. Usually the kit lasts for 6-12 months, depending on its quality and climate in the region.

Basic moments

To replace windshield wipers on Toyota RAV4 models, you should start with a short introduction. Frame, frameless and hybrid types of windshield wipers are used for the front, rear or passenger window of a car. Each of them is presented in the form of a huge list of suitable models. It is better to give preference to original parts - there will be fewer problems.

Fourth generation RAV4

The latest Toyota Rav 4 model available to customers has been produced since 2012. The length of the driver's brush is 650 mm, the passenger's is 400 mm. Fastening type: hook.

Popular wiper models: Valeo Silencio X, Kamoka set, Bosch Twin, Eco.

The replacement procedure is carried out as quickly as possible due to the fixing cap on the windshield wipers. Open it, lift the leash, pull it towards you and easily remove the brush. Pull out the elastic from the side where the lock is installed. We remove the metal guides installed on both sides of the part. We attach them to the new elastic band, paying attention to the location of the fixing ebb. We start the guide brushes in the reverse order.

Be sure to snap the lock into place, otherwise the rubber band with guides will simply fall out during use.

We return the wiper to its place. If the brush is located along the lower glass lining, you can safely attach it. Afterwards, we make sure to check that the work is working properly.

How to remove wipers from a Toyota Rav4 car correctly

You should study the features of fastening the elements. They are different front and back so the performance will be different. Regarding the design, it is important to remember the following:

1. The front part uses two elements of different lengths. The driver's wiper is much larger than the passenger's. Fastening is carried out using a standard hook on the leash. This system is found on most domestic and foreign cars, so there are usually no difficulties with purchasing brushes and replacing them. A special lock holds the connection in the correct position and prevents the wipers from moving during operation.
2. A small brush is installed at the rear to improve visibility in difficult weather conditions. It is secured using a modern fastener, which consists of a specially configured hook at the end and a latch to prevent the working unit from moving.

Most often, no tools are needed for the job. The only thing you may need is a small flat-head screwdriver, but this can be replaced with any other item of suitable size.

Front

The work can be done anywhere, the main thing is that there is normal lighting. You can cover part of the hood with fabric to rest on and prevent scratches. Instructions:

1. Using a small flat head screwdriver, gently pry the retainer until it releases and lifts up. It is held on by latches, and if the wiper has not been changed for a long time, considerable force may be required, since the connection may become deformed or clogged with dirt over time.
2. Grasp the wiper with your hand and pull it away from the retainer. It holds quite tightly, so you first need to apply some force to move it out of place. Then the element is simply removed.
3. Since the wiper arm is spring-loaded, hold it with your other hand so that after removal it does not hit the glass. If some elements do not lend themselves, you can treat the connection with a liquid key, then it will come off much easier.

By the way!

Place a napkin or rag folded in several layers between the leash and the glass to eliminate any possibility of damage to the surface.

When purchasing, it is important to choose the right wipers. Their parameters vary depending on the generation of Toyota RAV4. The easiest way is to use a list:

1. 1st generation - from 1994 to 2000. The length of the driver's wiper is 51 cm, the passenger's is 45.5 cm.
2. 2nd generation - from 2000 to 2005. The driver's brush is 61 cm, the passenger's is 48 cm.
3. 3rd generation - from 2005 to 2013. On the driver's side - 61 cm, on the passenger side - 40.5 cm.
4. 4th generation - from 2013 to 2021. The length of the driver's brush is 65 cm, the passenger's is 40.5 cm.
5. 5th generation - from 2021 to 2021 left side - 65 cm, right side - 40 cm.

You can purchase original kits for your car model, or buy brushes separately. The second option most often allows you to save significantly.

Rear: replacement

Most often, the rear brush is replaced at the same time as the front brush. But if this unit is rarely used, you can install a new one every other time. Replacement instructions:

1. Lift the plastic plug at the base of the structure where it attaches to the car body. To do this, pull it up. If this is difficult to do with your fingers, use a flat-head screwdriver to pry it off. The element is simply folded over, and not removed completely.
2. Pull the leash at a 90-degree angle to make it easier to work with. It is fixed in this position.
3. Rotate the wiper so that it comes out of the tabs. Then gently pull it away from the leader to remove the pin from the hook. Move the part in different directions to select the optimal position for removal.
4. Place the new element in place of the old one; to do this, snap the pin into the hook, then move the frame to the leash so that it locks in the correct position.
5. Reinstall the wiper and make sure it presses against the glass evenly along its entire length. Snap the plug into the base.

By the way!

Remove the protective element from the rubber band after installation so as not to damage it or erase the graphite coating if accidentally touched.

It is also important to choose the right size wiper depending on the generation of the car. The length of the first is 35.5 cm, the length of the second and third is 30.5, and the fourth and fifth are 25 cm.

Third generation RAV4

The model was produced from 2005 to 2012 with a brush mounting type - hook. Its length for the windshield is 600 mm, for the passenger window – 400 mm.

Available options:
SWF VisioNext, Bosch Eco, Hybrid model from Denso.

To change the brush, you must first remove it. Pull up the latch located in the center of the structure. Open it with a fingernail or a screwdriver. We lift the leash and move the wiper back, removing it from the hook. We replace the brush with a new one and repeat the work in reverse order. We carry out a similar replacement with the second windshield wiper. When checking the performance of the wipers, we pay attention to the brushes themselves - they should not touch the lining. Otherwise, you will have to change the installation of the levers.

Malfunctions

If the windshield wiper does not work after replacement, you need to determine where exactly the problem lies. To do this, you need to disconnect the plug box from the switch located under the dashboard by connecting its terminals to the terminal block of the last node. The brushes have resumed operation - the switch is faulty, everything remains as before - the problem is in the replacement unit itself. It is also possible that the wiper operates at high and low speeds, but does not move in intermittent mode. In this case, you will have to look at the node relay.

If such a procedure is too complicated for the average vehicle owner, it is much easier and faster (but not cheaper) to have the car repaired. Parts can be replaced by experienced workers in a matter of minutes.

Thanks to watching the visual video, there should be no problems with replacing the original wipers.

Wipers on Toyota RAV 4

Windshield wipers are an important structural element of the vehicle body, which is responsible for the comfort of visibility - if there are streaks or other signs of reduced efficiency, the wipers on the RAV 4 must be replaced. Fortunately, this does not cause any difficulties.

Replacing wiper blades is not the only problem that motorists may have - they also need to choose the right wiper blades. Please be aware that installing an incompatible set of parts may cause the windshield to warp and reduce the driver's and passenger's visibility.

The Toyota RAV 4 body supports most common wipers of compatible sizes, which allows you to install even analogues of original components. The locking system for the front windshield wipers is a “hook” system, while the rear window uses a “hook with an additional hinge” format.

The latest generation of Toyota RAV 4 is the CA40 generation, which is characterized by changes in the structural features of the body and power unit. Windshield wipers for the latest version of RAV 4 are identical to the previous generation, and are also completely interchangeable with the restyling and pre-restyling versions.

Original articles

A genuine set of windshield wipers is the best option for replacement, as it fully takes into account the structural features of the vehicle body. The average cost of stock wipers varies between 800-1300 rubles per set, official articles - 3397010297, 3397013434, 3397010RR.

Replacement options

Analogues of original components are often purchased in order to save on vehicle maintenance - often such parts have a level of quality that is not inferior to the original ones, but have a lower cost, which is characterized by the absence of overpayment for the brand.

The most popular alternative windshield wipers are the following models:

Note! If you purchase a non-original set of windshield wipers, it is important to check the parts for compatibility with the vehicle’s VIN code on the manufacturer’s official website.

Frame

Frame wipers are a two-component structure consisting of a metal frame and a removable brush. Characterized by low cost and low maintenance. A popular model for RAV 4 is SWF VisioNext, article number 119860.

Frameless

The main feature of frameless wipers is their aerodynamic design, which ensures low noise levels and tight fit. A popular model is Valeo Silencio, article number 567947.

Hybrid

The design of hybrid windshield wipers combines all the advantages of frame and frameless types - wipers are characterized by high efficiency and a long service life, but have a high cost on the market. The most popular options for Toyota RAV 4 are Trico Hybrid, part numbers hf480 and hf485.

Winter

A specialized type of windshield wipers designed for use in cold weather. Resistant to temperature changes and prevents the risk of glass deformation if there is a crust of ice on its surface. The Bosch “AR601S” is considered a proven option.

CA40

The latest generation of Toyota RAV 4 is the CA40 generation, which is characterized by changes in the structural features of the body and power unit. Windshield wipers for the latest version of RAV 4 are identical to the previous generation, and are also completely interchangeable with the restyling and pre-restyling versions.

Original articles

A genuine set of windshield wipers is the best option for replacement, as it fully takes into account the structural features of the vehicle body. The average cost of stock wipers varies between 800-1300 rubles per set, official articles - 3397010297, 3397013434, 3397010RR.

Replacement options

Analogues of original components are often purchased in order to save on vehicle maintenance - often such parts have a level of quality that is not inferior to the original ones, but have a lower cost, which is characterized by the absence of overpayment for the brand.

The most popular alternative windshield wipers are the following models:

Replacement

Installing a new set of windshield wipers on the latest generation RAV 4 will not cause any particular difficulties even if you do not have practical skills in servicing the car - the entire process is carried out according to an intuitive scenario and takes no more than 20 minutes. To replace the windshield wipers, you will need a slotted screwdriver or pliers, as well as a piece of foam rubber or a small cloth for cushioning. Replacement occurs as follows:

• To begin, move the metal frame of the windshield wipers away from the windshield and place a small soft cloth: a towel, foam rubber or rags for wiping. The fact is that the degree of pressing to the surface of the windshield is determined by a mechanism with a spring, which can work when servicing the windshield wipers and deform the glass;
• Next, using a screwdriver or pliers, unclip the latch that secures the wiper blade to the frame and pull out the worn part by moving it upwards and towards you. The “hook” type fastening itself is located on the back side of the windshield wipers at the bottom of the blade;
• Then we carefully lubricate the frame seats with technical lubricant, which will prevent metal corrosion, and install new brushes, after which we fix the new elements. We repeat a similar procedure with the second wiper.

The rear wiper is changed in the same way, but the clips are removed from the inside of the trunk door after first releasing the decorative plug.

Instructions for removing and replacing wipers

It is very easy to replace used material, and you can do it yourself. The only thing that is important to do is to buy a new part that is the same size as the old one. After all, wipers often differ in length from each other and this is also important to take into account.

Dismantling occurs in stages:

1. The lever is placed vertically and removed from the windshield. It is important to hold it carefully so as not to injure it. If it pops out, it may damage the glass.
2. Now you need to open the holder cap and pull the brush down, while holding the holder firmly.
3. After this, you need to take the previously stored part, put it on the knitting needle and close the cap. Now pull it down, leveling it out. Thus, the operation is completed and you can proceed with another window cleaner. It is filmed in exactly the same way (the author of the video is TheBrandConnect).

Features of replacing rear wipers

There are some car models on which it would also be a good idea to install rear window wipers. The installation pattern on the rear windows is quite different from the installation of the glass cleaner on the front windows. In the case of installing rear wipers, it is impossible to say how to change the wipers, because all cars are different and the approach to them is individual. As an example, we can take the usual Lada Kalina station wagon.

1. There is a fastening nut on the wiper, and above it there is a protective element. This metal cap must be lifted up.
2. Then take a 10mm wrench and, carefully, so as not to drop the washer under it, unscrew the nut. Now turn the device a little and carefully pull it towards you. It will come off without any problems. After this, you can remove the mechanism to clean the windows.
3. Now, on the dismantled device, you need to pull the part and use a screwdriver to loosen the latch that holds the part to the lever. You can replace it in the same way as replacing front windshield wipers. When buying brushes, you need to pay attention to the bend of the brush, because even this affects the quality of cleaning

   
   Varieties of design

Wipers on Toyota RAV 4

Windshield wipers are an important structural element of the vehicle body, which is responsible for the comfort of visibility - if there are streaks or other signs of reduced efficiency, the wipers on the RAV 4 must be replaced. Fortunately, this does not cause any difficulties.

Replacing wiper blades is not the only problem that motorists may have - they also need to choose the right wiper blades. Please be aware that installing an incompatible set of parts may cause the windshield to warp and reduce the driver's and passenger's visibility.

Year of manufactureGeneration - body Driver's side Passenger's side Rear Mounting type

The Toyota RAV 4 body supports most common wipers of compatible sizes, which allows you to install even analogues of original components. The locking system for the front windshield wipers is a “hook” system, while the rear window uses a “hook with an additional hinge” format.

The latest generation of Toyota RAV 4 is the CA40 generation, which is characterized by changes in the structural features of the body and power unit. Windshield wipers for the latest version of RAV 4 are identical to the previous generation, and are also completely interchangeable with the restyling and pre-restyling versions.

Original articles

A genuine set of windshield wipers is the best option for replacement, as it fully takes into account the structural features of the vehicle body. The average cost of stock wipers varies between 800-1300 rubles per set, official articles - 3397010297, 3397013434, 3397010RR.

Replacement options

Analogues of original components are often purchased in order to save on vehicle maintenance - often such parts have a level of quality that is not inferior to the original ones, but have a lower cost, which is characterized by the absence of overpayment for the brand.

The most popular alternative windshield wipers are the following models:

ManufacturerArticleCountry of productionStructural locationApproximate cost, rub.

Note! If you purchase a non-original set of windshield wipers, it is important to check the parts for compatibility with the vehicle’s VIN code on the manufacturer’s official website.

Frame

Frame wipers are a two-component structure consisting of a metal frame and a removable brush. Characterized by low cost and low maintenance. A popular model for RAV 4 is SWF VisioNext, article number 119860.

Frameless

The main feature of frameless wipers is their aerodynamic design, which ensures low noise levels and tight fit. A popular model is Valeo Silencio, article number 567947.

Hybrid

The design of hybrid windshield wipers combines all the advantages of frame and frameless types - wipers are characterized by high efficiency and a long service life, but have a high cost on the market. The most popular options for Toyota RAV 4 are Trico Hybrid, part numbers hf480 and hf485.

Winter

A specialized type of windshield wipers designed for use in cold weather. Resistant to temperature changes and prevents the risk of glass deformation if there is a crust of ice on its surface. The Bosch AR601S is considered a proven option.

Replacement

Installing a new set of windshield wipers on the latest generation RAV 4 will not cause any particular difficulties even if you do not have practical skills in servicing the car - the entire process is carried out according to an intuitive scenario and takes no more than 20 minutes. To replace the windshield wipers, you will need a slotted screwdriver or pliers, as well as a piece of foam rubber or a small cloth for cushioning. Replacement occurs as follows:

• To begin, move the metal frame of the windshield wipers away from the windshield and place a small soft cloth: a towel, foam rubber or rags for wiping. The fact is that the degree of pressing to the surface of the windshield is determined by a mechanism with a spring, which can work when servicing the windshield wipers and deform the glass,
• Next, using a screwdriver or pliers, unclip the latch that secures the wiper blade to the frame and pull out the worn part by moving it upwards and towards you. The “hook” type fastening itself is located on the back side of the windshield wipers at the bottom of the blade,
• Then we carefully lubricate the frame seats with technical lubricant, which will prevent metal corrosion, and install new brushes, after which we fix the new elements. We repeat a similar procedure with the second wiper.

The rear wiper is changed in the same way, but the clips are removed from the inside of the trunk door after first releasing the decorative plug.

How to choose the right wipers for Toyota Rav4

All three types that are commercially available are suitable for the model, so you can use any one. First of all, consider the size and type of fastening. As for the design, each option has its pros and cons:

1. Frame. A classic variety that has been used longer than others and has proven itself well in use. The clamping system ensures good quality glass cleaning even during heavy rains. But the resource of this type is an order of magnitude less, since the frame loses its rigidity over time and does not press so well. And the rubber bands used wear out faster than their analogues. It should also be noted that the aerodynamic properties are not the best and the quality of cleaning at high speed is deteriorating.
2. Frameless. In this design, the rubber part is pressed against the glass surface using an elastic holder made of impact-resistant plastic. They are most often chosen for their modern appearance and good surface cleaning quality. The resource is an order of magnitude greater, and is better suited for use in winter, as it freezes less and maintains mobility even in frosty conditions. It is worth purchasing high-quality products, since cheap ones do not provide the necessary pressure to the curves of the glass, which is why the edges may not be cleaned well.
3. Hybrid. They combine the advantages of frame and frameless construction. They are a system that is pressed tightly to the surface and is closed from the outside with a plastic casing, which prevents freezing and ensures good aerodynamics. It is also worth noting the long service life, since the casing protects the rubber from adverse influences. But hybrid wipers are also the most expensive. The situation is simplified by the fact that it is easy to change the rubber bands on them yourself, and this is a significant saving.

By the way!

At the factory, Toyota RAV4 is equipped with hybrid designs.

Any driver can replace wipers on a RAV4 thanks to the classic design of the mounts and the availability of new parts. The main thing is to choose the appropriate size for your generation of car and follow simple instructions. To understand the issue even better, you can watch the video.

Choosing windshield wiper blades for Toyota Rav 4

Rav 4 wipers are an element of the windshield (and rear) glass cleaning system that provides the necessary visibility of the road. Consumables must reliably clean constantly dirty glass and not wear out quickly. The size of the brushes of different generations changed, with the rear element and the front passenger one becoming smaller over time, and the part on the driver’s side, on the contrary, became longer (on the latest generation - 650 mm). Below we will talk about the types of wipers, manufacturers and nuances of replacing this accessory on a Toyota Rav 4 car.

Dimensions of Rav 4 twins

Generations Rav 4 and years of production Driver (cm) Passenger (cm) Rear (cm)

What types of windshield wiper blades are there?

The following types of windshield wiper blades can be installed on Japanese Toyota Rav 4 crossovers:

• frame;
• frameless;
• hybrid.

Each type has advantages and disadvantages.

Frameless wipers

The body of the frameless brushes is made of rubber and plastic, and the glass cleaning strip is fixed inside. The advantage of this design will be resistance to warping and icing , and good aerodynamics . The brush fits tightly onto the windshield. Replacement of worn-out blades is carried out without installing a new housing. As a result, this type of brushes for Rav 4 belongs to the all-season class.

Components of frameless

A design flaw manifests itself when installed on some car models - without installing an additional adapter, fastening is impossible. A number of manufacturers provide windshield wipers with adapters, but installation difficulties may arise.

Good producers

Glass cleaners for Rav 4 crossovers are supplied to the market by both Russian and foreign manufacturers. The choice of windshield wiper blades is wide, but it is better to buy products from well-known companies: Bosch, Trico, Valeo, Denso and Champion.

Bosch products are reliable and durable. The manufacturer has established itself as the creator of a high-quality and high-tech product, and automotive consumables are not the only segment of the group of companies’ activities.

Trico is a company with history that began producing windshield wipers at the beginning of the last century. Today the brand is considered one of the best car accessories on the market.

Valeo is a concern that supplies components for automobiles to the largest automakers. Valeo wipers are reliable and constantly improved.

The Japanese manufacturer Denso is working on the creation of automotive components; the production of windshield wipers is one of the company’s directions. As a supplier of automotive consumables, Denso ranks second in the global ranking.

Denso has been a long-time supplier of brushes for Toyota.

Wipers for Toyota Rav 4 are supplied by all of these companies. Which one to choose, everyone decides for himself.

Changing wipers on Toyota Rav 4 3

How to change worn windshield wiper blades? On the third generation Rav 4 crossover, windshield wipers are replaced in the following order:

1. The latch holding the brush is pulled up . To do this, it is better to use a screwdriver to avoid damaging your nails.
2. The leash is raised, the wiper is retracted.
3. The brush carefully removed . You need to release the leash smoothly, because if you pull back sharply, it can break the windshield.
4. The new brush is removed from the packaging and replaced with the old one . The latch snaps into place .
5. The procedure is repeated with the second wiper.

The Rav 4 has a hook type of attachment.

Original wipers Rav 4 3 can be ordered online. The part number for the passenger side wiper is 85212-42120. Its length is 405 mm. The article number for purchasing consumables on the driver’s side is 85222-42110. Its size is larger - 610 mm.

Types of wiper mounts

There are several options for fixing windshield wipers, each of which has its own advantages and disadvantages:

• side pin;
• button;
• narrow button;
• side mount;
• side clamp;
• top lock;
• bayonet lock;
• claw.

Rav 4 windshield wiper blades use a “hook” mount. It is considered a classic.

Until 1999, the method was used on all cars without exception. However, then Ford decided to change the system and began installing different types of mounts on the windshield wipers. Other manufacturers followed the example of the North American concern. But Japanese companies still use the “hook”.

Most often, the mount has standard dimensions of 9 by 4 or 9 by 3. Very rarely, other parameters are found: 8 by 3 (can be used for a passenger wiper).

The “side pin” method of fixing windshield wipers is popular among German concerns. It began to be used in 2005. This mount is used on Audi, Mercedes-Benz, VW, BMW models.

Sometimes the "side pin" is used in Volvo and Peugeot cars. The length of the fixing element is 22 mm. The 17 mm mount appeared in 2009 on some BMW vehicles.

The “button” is common on cars from European manufacturers. It is used in VW, Citroen, Volvo, Renault. The mount is square with a side of 19 mm.

Since 2010, they began to use a “narrow button”. The side length of the square retainer has been reduced to 16mm. It was installed on VAG cars.

Side mounting is common in Renault cars. Other automakers use it much less frequently.

The popularity of the “side clamp” fixation method is comparable to the classic “hook”. Wipers are “clamped to the side” on cars of the brands Saab, Audi, Opel, Fiat, Mercedes-Benz.

The "top lock" is very similar in appearance to the "side clamp". However, the fixation method is different. This type of installation is used on BMW 5 and 6 series cars.

Owners of Renault and Saab cars know about the “bayonet lock” method of fixing windshield wipers. Fastening began to be used after 2004. Trucks use a similar method. But the design of their wipers has two holes.

“Claw” is less common than the others. It is used only on modern versions of the Audi A6. No one else uses this method of fixation.