Trunk in Toyota Camry 40: dimensions, how to increase volume

The trunk of the Toyota Camry V40 can be of two sizes.
It depends on the configuration of the car. For example, the Toyota Camry in the “Comfort”, “Elegance” and “Prestige” trim levels has a trunk volume of 535 liters. In the top-end “Luxe” configuration it will be slightly smaller – 504 liters. In 2009, the Camry 40 version was slightly modified, i.e. there was a restyling, but this did not affect the size of the trunk in any way. It remained the same size as it was.

The trunk dimensions of the Camry are as follows: the width at the very edge inside is 1640 mm, the bottom width between the wheel arches is 980 mm, the depth from the threshold to the seats is 980 mm.

Advantages of the Toyota Camry roof rack

Such details have several advantages. They distinguish them favorably from conventional car racks:

• Load capacity. By installing this product on the roof of a Toyota Camry, you can place all large and long items in it and go about your business. Despite its rather modest dimensions, the design has good load-carrying capacity.
• Comfort. Due to the fact that all things will be on the roof of the Toyota Camry, the interior will become empty. You won't need to occupy the back seat with bags and packages for your trip.
• Safety. Some Toyota Camry owners are worried that the roof structure will block their view. In fact, all the accessories for this car model are designed in such a way that they do not interfere with the driver during the trip. Things loaded onto the roof of a Toyota Camry will not pose any danger to you even in the event of an accident.
• Simplicity. You can install a roof rack on your car in just a couple of hours. Of course, the duration of installation depends on the type of structure you choose. In addition, you can easily remove the trunk and drive without it.

Car roof rack

• Uniform placement of cargo. By overloading a regular trunk, a person reduces the ground clearance of the Toyota Camry and increases the possibility of the car tipping over. If you place some of your things in the roof rack, the load will be distributed evenly.
• Acceptable price. Such a product for a Toyota Camry will cost the car owner several thousand rubles.
• Strength. The trunk is created from pipes with a diameter of 25 mm and a thickness of 1.5 mm. This ensures the correct balance between weight and load-carrying capacity of the device. In addition, manufacturers use steel or aluminum pipes, which increases the strength of the product. To fix the product on the roof, strong fasteners are used, which virtually eliminate the possibility that the rack will come off during a trip.
• Versatility. You can use the product in any weather. In the summer, drivers transport camping equipment in the devices, and in the winter they load them with skis.
• Economical. Some drivers do not install such a product on the roof of their Toyota Camry because they consider it uneconomical. They think that the trunk greatly increases gas mileage. In fact, with a roof structure, over a hundred kilometers you will spend about 300 ml of fuel more than without it. Of course, gasoline consumption is affected by the streamlining of the part: the higher it is, the less fuel is consumed.
• Attractiveness. Due to the fact that the device on the roof of the car can be equipped at your own discretion, you will increase the attractiveness of the car and increase its functionality.

Car roof box

This is interesting: Cabin filter Nissan X-Trail t31: where is it located, replacement

Full technical specifications of Toyota Camry XV70 (2018 model year)

Disadvantages of the Toyota Camry roof rack

Not all car enthusiasts are attracted by the number of advantages of this design. Some drivers are confused by several disadvantages that the Toyota Camry roof rack has:

• noise. The roof structure reduces the vehicle's resistance to air flow. Because of this, it becomes noisy inside the car;
• sustainability. After installing the product, the Toyota Camry's resistance to strong side winds decreases slightly.

Aerodynamic roof bars

How to choose a roof design for a Toyota Camry

Take a good look at your Toyota Camry before purchasing a roof rack. Several types of products are installed on this car model:

• Smooth roof design. If the Toyota Camry does not have roof rails or standard seats, then the trunk is installed in the doorway.
• The product is in standard places. This is how the structure is mounted on the roof of a car if it has small hatches covered with covers.
• Roof rack. If the car is equipped with such longitudinal arches, then the device is attached to them.

Aerodynamic roof rack

Simple, strict style

The design of the car looks simple, Toyota has never been an innovator in the field of appearance, competitors are more beautiful. There are narrow headlights, directed downwards, equipped with halogen or xenon lamps. The rounded shapes of the Camry's hood flow like lines towards the strict radiator grille, which in the restyling is covered with chrome.

The bumper is equipped with optics washers and fog lights recessed at the bottom. Restyling brought a slightly different bumper with PTF in a chrome trim.

On the side there are powerful massive forms with a slight swelling of the arches. The business-class image is supported by chrome window surrounds and a straight line leading to the rear lights. The rear lights are identical in shape to the front ones. The trunk lid has a raised shape, creating a powerful image together with the massive bumper.

It was the concentration of design on rigor that pleased officials, who are the main consumers of the model. The car looks simple, but is relatively luxurious.

The dimensions of the sedan have grown:

• length – 4815 mm;
• width – 1820 mm;
• height – 1480 mm;
• wheelbase – 2775 mm;
• ground clearance - 160 mm.

How to install a structure on the roof of a Toyota Camry

Installing the product is a simple task, so you can easily handle it yourself. This way you will save money on paying for the services of service specialists and will be confident in an excellent result of the work. Once you have selected the ideal rack, proceed to install it:

• Preparing for work. Do not install the structure on a dirty roof - the result of the work may not meet your expectations. If such a device has already been installed on the Toyota Camry, polish the roof surface. This way you will return the car to its original color, which has faded in the sun due to long-term use of the structure.

Roof rack Toyota Camry

• Installation of the structure. Installation features depend on the type of product: if you are installing the trunk in a doorway, open the doors before installation. After this, fix the special stops on the stiffening ribs and grab the doorway with your paws. Manufacturers cover the paws with plastic and rubber, so the Toyota Camry paint is not scratched when using the device;
• if you fix the device in standard places, then simply screw it to the welded nuts. Remember that you don’t need to tighten it too tightly - this way you can pull out the top of the car roof;
• The easiest way to fix the trunk is on the roof rails. This installation allows the driver to easily move the crossbars along the entire length of the roof rails. Thanks to this, you can easily adjust the size of the structure to the volume of the load. In addition, the roof rails have several support points, and this increases the pressure area of ​​the product and reduces the load on the Toyota Camry. Of course, when purchasing a device, consider the length of the rails.

Features of USB adapters for

It is not convenient to constantly record music and audio books for listening in the car onto discs. It’s easier to use a flash drive and a phone, but the native multimedia system of the Camry V40 does not have such functions, so car enthusiasts install USB adapters.

Advantages of installing an MP3 adapter in Toyota Camry V40:

• You can do the installation work yourself
• the cost of the device is not high
• Steering wheel music control is retained
• The CD changer continues to operate normally.

To install the USB adapter, you need to disassemble the head unit, this process is described above. Next, the MP3 adapter is pinned out, the cord is inserted into the plug of the CD changer at the back, be careful into the 12-pin connector (6+6). The adapter can be hidden behind the stock head unit.

It is best to pull the USB and AUX cords into the glove compartment to the farthest hole because the glove box guides move closer to it. To use a USB flash drive (flash drive) in a car, you need to format it in FAT32, create folders CD1, CD2, etc. and record music in MP3, WMA, AAC format. (The number of CD... folders that will be played depends only on the head unit and how many disks it is designed for). Jumping between the standard head unit and the adapter occurs after pressing the “DISC” button. Switching folders on a flash drive is similar to switching disks in a CD changer.

Pros of using an MP3 USB adapter:

• ability to play a large number of songs,
• Each folder can store up to 100 tracks,
• the last played song is saved,
• when started, the song plays from the moment at which it was interrupted,
• AUX allows you to play audio files from any device with a headphone jack.

Tips for using the product

Proper installation of the structure is not all that is needed. If you want to use your roof rack for several years, pay attention to our recommendations:

• load distribution. The exact load-carrying capacity of the structure depends on the brand of the manufacturer. In most cases, the trunk cannot be loaded with more than 75 kilograms. Remember to distribute the weight evenly. Experts advise sticking to the following ratio: ½ load between the beams and ¼ between the luggage of the front and rear parts of the structure. To find out the ideal weight distribution, load the device some time after installation and ride it for a few kilometers. This way you will know for sure whether the entire load is holding well;
• use of the product. If you do not use the structure every day, then remove it from time to time. Why do you need an empty roof rack that only wastes fuel?
• design verification. Periodically check the condition of the product on your Toyota Camry. If you notice a problem in time, you can easily fix it, saving time and money on a full repair;
• accuracy. A loaded trunk will not allow you to make sharp maneuvers and sharp turns on the road. In addition, if the structure is clogged to capacity, do not exceed the speed of 130 km/h.

Correctly installed car roof rack

By installing a roof rack on your Toyota Camry, you will save space in your car and give your car an attractive look.

Moscow Automobile and Highway State University, Moscow. Level of education: Higher. Faculty: AT. Specialty: Special engineer Cars and automotive industry. Experience in the automotive industry (master consultant...

This is interesting: Timing chain for VAZ 2107: do-it-yourself replacement

Car reviews

Yuri S., Krasnoyarsk

: Camry 2011, still running, I’ve been using it for seven years. Overall, the car is good, balanced, although the seating position is a little high compared to older Japanese sedans. When I switched to it from a Corolla, I felt like I was using an SUV. Especially when the seat is in the up position. But the ground clearance turned out to be normal, if you drive around the city, I don’t catch anything even in winter. The chassis, however, is tough on potholes, but it’s comfortable to drive on a dirt road even at 100 km/h. By the way, 100 is just the most normal speed for the 40th Camry. The only noticeable drawback is poor visibility from the interior.

Sergey N., Novosibirsk

: I had a 2009 Camry for 6 years. With a 2.4-liter engine and automatic transmission. A nice, spacious car with a huge trunk for a sedan. An easy-to-maintain car with conveniently located controls. The cabin is warm even in severe frosts. The rear backrests can be folded down to accommodate more cargo. The suspension is very reliable; it had to be repaired no earlier than after 200,000-250,000 km. The suspension is soft, the gearbox is reliable - the main thing is not to forget to change the filter and oil on time. But I think the engine is not entirely successful due to high oil consumption. Sometimes it came out to 400 g per 1000 km.

Konstantin B., Orel

: From 2007 to 2010 I used a Camry XV 40, I drove more than 200 thousand km on it. In short - an almost indestructible model. I haven’t ridden it anywhere, except perhaps off-road. I changed almost nothing except consumables. Yes, and without major repairs. Well, maybe I repaired the gearbox at 120 thousand km. And still, in terms of reliability and quality, I have never had a better car.

Handbrake adjustment

In order to check the correct operation of the parking brake, you need to raise the handbrake. When lifting, the driver should hear 7 - 9 clicks. If the number of clicks does not correspond to this number, then this indicates a malfunction in the brake system.

The need for adjustment arises when the car's mileage reaches 17-25 thousand km. In order to learn how to tighten the handbrake on a Toyota Camry 40 and adjust it, it is recommended that you read the instructions below.

• Pull out the rubber plug.
• Position the inspection hole at the lowest point, as shown in the photo below.

• Using a flashlight we find the adjusting gear.
• Using a screwdriver, you need to get between the teeth and turn the gear up. During this process, the driver will hear the sound of a spring. It is important not to overtighten the gear. The rotation of the discs should be soft and smooth with a slight sound of the pads rubbing.

• Adjust the opposite wheel in the same way, maintaining symmetry. Otherwise, there may be a difference in setting. Because of this, the body will move to the side when trying to move off on a slope.
• Reinstall all parts in reverse order.
• Release the handbrake and check the rotation of the rear wheels. They must walk freely.

Installation of aerodynamic body kits

Tuning a Toyota Camry is a rather complex process, and its implementation can only be entrusted to professionals in specialized services. But in our country there are many villages and small towns where such services are not provided, so in such a case these tips will come in handy:

1. Most often, original products from Japan, Germany, Korea or other countries fit exactly in shape and fasteners, but still, before painting, check that the fasteners and sizes of all parts of the kit match. Sometimes you have to trim to get a perfect match.
2. During long-term storage and improper transportation of tuning kits for Camry, the geometry of individual parts changes, and during installation, gaps appear or, conversely, part of the kit does not fit into its place. For precise installation, evenly heat the maximum contact area to a temperature of 60°C - the fiberglass will become elastic and take the desired shape. For direct installation in such cases, use a hairdryer to heat the area.
3. If you find damage in the form of bubbles or gouges on the outside of the kit part for Toyota Camry, you need to remove these irregularities using ordinary automotive putty.
4. When drying parts after painting, the temperature should be kept within thirty-five degrees. A proven method for drying body kits for Camry 50, 40 and 30 is to increase the drying time at normal room temperature.
5. If it is not possible to immediately install the body kit on the car, choose a dry room and install the part in the position in which it should be on the car.
6. Thresholds are usually installed after painting and fitting using automotive glass sealant. Before this, they are degreased, a layer of sealant is applied, after which they need to be fixed for several hours. Another method is used extremely rarely, because self-tapping screws spoil the aesthetics and surface of the body.

Tuning for the subsequent Toyota Camry 30 is still popular, as is the 30th model itself. Bumper covers together cost 6 thousand rubles, the price of thresholds for Camry 30 is five and a half thousand rubles.

The body kit for Camry 40 will cost the buyer 11 thousand rubles. – it consists of sills and trims for both bumpers. The purchase of a spoiler for the trunk lid is not included in this amount - it is estimated at three and a half thousand rubles.

The price of body kits for the Camry 50 and 55 models is an order of magnitude higher - the skirts of two bumpers together with the door sills cost 89,500 rubles, another set from the Japanese manufacturer Asuka Japan, consisting of a front bumper along with a radiator grille, a hood trim and a rear bumper skirt, is estimated at 180 thousand rubles. Look at the photo how beautiful the painted and correctly installed front bumper on a Toyota Camry v 50 looks.

Replacing hand brake pads Camry 40

In order to replace the parking brake pads, you need to use the instructions given below.

• Remove the wheel from the side where the pads need to be replaced.
• Remove the brake disc. To do this, it is recommended to use a “14” key.

• Dismantle the springs of the front and rear pads.
• Remove the front and rear pads.
• Replace the pads and install everything in reverse order.

• Install the brake disc
• Adjust the operation of the hand brake.

Do-it-yourself replacement of upholstery and cleaning of Toyota Camry ACV seats & | interior of Toyota Camry ACV40

Rear

admin

Toyota Camry XV40. How to remove seats

In order to carry out the planned event successfully and without unnecessary risks and problems, you should use a slotted screwdriver, a wrench, and you won’t even need the help of a specialist.

Do-it-yourself replacement of upholstery and cleaning of Toyota Camry ACV40 seats. And we begin to remove the upholstery by snapping it off...

Therefore, if you need to remove the seats from a Toyota Camry, don’t be afraid, go for it! To remove the sofa, you will need to follow a few simple steps:

Next, remove the thresholds by simply gently pulling them up. Long pliers are a very important tool for removing the front pillars... Next, remove the rear backrest. This creates significant inconvenience for passengers.

Replacing the front hand brake cable of a Camry 40

It is recommended to change the cable in cases of severe stretching or mechanical damage. To replace it, you must use the instructions below.

• Disassemble the console, gaining access to the handbrake cable.
• Secure the threaded end with a wrench. After this, you need to disconnect the tension coupling. This operation will release the cable.
• Remove the cable clamp from the turnbuckle side.
• Unscrew the locknut and adjusting nut.
• Disconnect the front cable from the handbrake lever.
• Remove the holder mount
• Remove the cable from the car.
• Replace the cable with a new one and install the parts in the reverse order.
• Adjust the hand brake drive.

Checkpoints:

All luggage rack measurements are given based on control points, which are different for different cars, and in general have the following meaning:

• A: top left corner;
• B: top right corner;
• E: inseam to the far left (bottom corner);
• D: Inseam to the far right (bottom corner).

Important: in cases where the car does not have control points, the data is presented in the format length – width – height.

General view of the trunk

Caution: the above data are the official figures of the manufacturer, however, please note that the information is for reference only and does not guarantee absolute accuracy.

The trunk of the Toyota Camry V40 can be of two sizes. It depends on the configuration of the car. For example, the Toyota Camry in the “Comfort”, “Elegance” and “Prestige” trim levels has a trunk volume of 535 liters.

In the top-end “Luxe” configuration it will be slightly smaller – 504 liters. In 2009, the Camry 40 version was slightly modified, i.e.

there was a restyling, but this did not affect the size of the trunk in any way. It remained the same size as it was. The trunk dimensions of the Camry are as follows: the width at the very edge inside is 1640 mm, the bottom width between the wheel arches is 980 mm, the depth from the threshold to the seats is 980 mm.

Clearance

Nissan Qashqai trunk volume in liters

Russian drivers like the Chevrolet Cruze for its high ground clearance. It allows you to move freely around the city and countryside without worrying about the underbody of the car.

Officially, the ground clearance is 16 cm. But it is uneven along the length of the body; the rear clearance is much larger - 22 cm. This size is not enough for off-road use, but driving on potholes and dirt roads is smooth.

Of course, when the car is fully loaded and engine protection is installed, the ground clearance will be less. It can be increased using spacers on shock absorbers or large diameter wheels. The last option is the best way to make the car taller. Its disadvantage is that passengers will be more aware of road irregularities.

Judging by the reviews of car enthusiasts, the trunk size of the Chevrolet Cruze hatchback is quite sufficient. This car can transport skis, three-meter boards and slats. This will not affect the comfort of the rear passenger and driver in any way.

Compared to its C-class competitors, Cruze wins due to its more interesting design, spacious trunk, large space for rear passengers, and increased ground clearance. This explains its popularity in Russia and other countries.

Replacing the rear cable Camry 40

To replace the rear cable, the car owner needs to use the instructions given below.

• Check the brake position when released.
• Unscrew the locknut and loosen the cable tensioner adjusting nut.
• Dismantle the floor tunnel lining.
• Unscrew the fastening bolts and remove the floor reinforcement.
• Pull out the end of the rear cables and remove the cable sheath clamps.
• Disconnect the cables from the rear pads.
• Remove the cables from the brake shields.
• Remove the bolts securing the front cable holders.
• Disconnect the remaining holders in the same way.
• Remove the cable.
• Replace with a new one and install everything in the reverse order.

Adjust the parking brake cable.

Hi all! )))) There was still no time to work on the handbrake, and he no longer held it very well, the lever already had to be pulled to the “Into space” position)))) But he looked like “Sit on me, then stand up, and then again sit down))))) I decided to look for how to tighten it, I found a video (available in the BZ) but this is for a “scissor”, so I wondered: is it the same on the handbrake? I decided to check it myself + some of my subscribers were also interested.

So, tightening the handbrake using the all-known method, namely tightening the handbrake cable, is not the same because there is no adjusting nut under the car, it is located in the central tunnel and is covered with a pile of plastic.

1) Remove the wheel

By the way, I installed spacers for casting2) We take out the rubber plug, you will immediately see it, it is located on the brake disc body3) Now we set the inspection hole to the lowest point and find (using a flashlight) the adjusting gear

The photo shows a little bit of the gear itself.

But here’s a closer look 4) Now, in fact, the process of applying the parking brake pads. Use a flat screwdriver to get between the teeth of the gear and scroll it up, you will hear the characteristic sound of a spring, then check again by rotating the disk, you should hear the sound of the pads slightly rubbing, but don't overdo it! If you accidentally overtighten, simply push the gear back to release the pads. Repeat the operation on the opposite wheel, try to position the pads evenly and symmetrically to avoid any difference in grip. I checked it like this until I couldn’t turn the disk on the third click of the handbrake, but when I released it the disk rotated freely, with a slight catch on the pads, now the handbrake holds with a bang))) Everything turned out to be simpler than I thought))) Everyone thank you for your attention)))) Mileage: 172,000 km

The hand brake is used on the Camry 40 both with an automatic transmission and if a manual transmission is installed. It allows the car owner to stop on slopes and other uneven roads.

In this case, it is also impossible to move away without using the handbrake. It helps the car not to roll back, which prevents the car from getting into an accident.

Camry trunk volume

Below are data on trunk volumes of Toyota Camry cars with various body types of different generations. For one generation of Camry, trunk volume differs depending on the configuration. This is due to the presence of an electric mechanism for adjusting the rear sofa in expensive versions (as a rule, in such configurations the rear seat backs do not fold). So, size data (about models presented on the Russian market):

• XV70 – 493 l;
• XV55 – 506 l, 483;
• XV50 -506 l, 483;
• XV40 - 535 l, 504;
• XV30 – 587 l;
• XV20 – 520 l;
• XV10 – 517 l.

The red hybrid Camry 70 is unlikely to become popular in Russia

Trunk volume Skoda Octavia 2012, 3rd generation, liftback, A7

What is the trunk volume of the Lada Kalina station wagon in liters?

Skoda Octavia 2016 review

Handbrake adjustment

In order to check the correct operation of the parking brake, you need to raise the handbrake. When lifting, the driver should hear 7 9 clicks. If the number of clicks does not correspond to this number, then this indicates a malfunction in the brake system.

The need for adjustment arises when the car's mileage reaches 17-25 thousand km. In order to learn how to tighten the handbrake on a Toyota Camry 40 and adjust it, it is recommended that you read the instructions below.

• Pull out the rubber plug.
• Position the inspection hole at the lowest point, as shown in the photo below.

• Using a flashlight we find the adjusting gear.
• Using a screwdriver, you need to get between the teeth and turn the gear up. During this process, the driver will hear the sound of a spring. It is important not to overtighten the gear. The rotation of the discs should be soft and smooth with a slight sound of the pads rubbing.

• Adjust the opposite wheel in the same way, maintaining symmetry. Otherwise, there may be a difference in setting. Because of this, the body will move to the side when trying to move off on a slope.
• Reinstall all parts in reverse order.
• Release the handbrake and check the rotation of the rear wheels. They must walk freely.

Basic elements of a car suspension

Any pendant consists of several basic elements:

Tires. This is the first stage in the system for smoothing out uneven road surfaces. Having a certain degree of elasticity, the tire is able to dampen a small amount of vibrations that occur during movement. If there are malfunctions in the tire suspension, the wheels can act as an indicator of a malfunction, since the service life of the tire in such a situation is quickly reduced and uneven wear occurs.

Basic elastic elements. The elastic elements of a car suspension include springs, leaf springs and torsion bars. The purpose of these elements is to provide an elastic connection between the body and the road surface. The entire load of the car falls on the springs, and due to their elasticity, the body is held at a certain height. During operation and heavy overloads, the metal of the elastic elements wears out, causing their rigidity to change. Such changes negatively affect the performance of the suspension as a whole. The angle of the wheels changes, the ground clearance decreases, and the load capacity decreases. Body sagging when unloaded is the main signal that the springs need to be replaced.

Additional elastic elements. Additional elastic elements include compression buffers; their use is necessary to dampen high-frequency vibrations, as well as vibrations generated during the contact of metal elements. Thanks to the presence of such elastic elements, the service life of other suspension components is significantly increased.

It is extremely important to monitor their good condition and promptly replace worn parts.

Guiding devices. The main task of the guide devices is to ensure the movement of the wheel in the established plane. Thanks to a system of levers, when moving on an uneven surface, the wheel moves in a vertical direction, while maintaining a perpendicular position relative to the road surface

Any violations in the guide elements will lead to rapid and uneven wear of the wheel tire, as well as other suspension elements.

Damping element. The element of the damping device is a shock absorber. The use of shock absorbers in the suspension system allows you to solve problems such as body vibration when driving on uneven roads, as well as smoothing out vibrations on other elements of the vehicle's suspension. Thanks to the damping function, constant contact of the wheel with the road is ensured, the car becomes more stable when driving.

Anti-roll bar. When turning at speed, the anti-roll bar prevents the vehicle from rolling. When performing a turning maneuver, the wheels on one side of the vehicle begin to lift off the road, which can cause the vehicle to roll over. At this moment, tension is created on the stabilizer, which tends to return the rising edge of the car to its place.

Fastening elements for individual parts. Fastening elements include ball joints, silent blocks and bolted joints that connect the remaining elements of the vehicle's suspension.

Increasing the volume of the luggage compartment

It happens that the trunk volume does not always correspond to the size of the car. Fortunately, the Toyota Camry is a business class car and the manufacturer has provided it with a spacious luggage compartment. But, if this space is not enough for you, we offer several options to increase the internal dimensions of the car trunk:

Trunk Camry XV50

• Since this car is equipped with a full-size spare tire, which takes up a lot of space, you can replace it with a spare tire, which takes up much less space. To do this, you will not only have to replace the spare tire itself, but also remove the plastic organizer for fastening the full-size spare tire, and instead install a “dock” mounting bolt (sold in any car store);
• when transporting large cargo, the most logical, albeit temporary, solution would be to lower the backrests of the rear seats (we remind you that this function is not available in all trim levels);
• choose trunk mats that are sized for a specific type of car. In absolute terms, this will increase the trunk volume of your Camry slightly, but will make operation more comfortable and ergonomic.

  Good looking

Replacing hand brake pads Camry 40

In order to replace the parking brake pads, you need to use the instructions given below.

• Remove the wheel from the side where the pads need to be replaced.
• Remove the brake disc. To do this, it is recommended to use a key of 14.

• Dismantle the springs of the front and rear pads.
• Remove the front and rear pads.
• Replace the pads and install everything in reverse order.

• Install the brake disc
• Adjust the operation of the hand brake.

Replacing the front hand brake cable of a Camry 40

It is recommended to change the cable in cases of severe stretching or mechanical damage. To replace it, you must use the instructions below.

• Disassemble the console, gaining access to the handbrake cable.
• Secure the threaded end with a wrench. After this, you need to disconnect the tension coupling. This operation will release the cable.
• Remove the cable clamp from the turnbuckle side.
• Unscrew the locknut and adjusting nut.
• Disconnect the front cable from the handbrake lever.
• Remove the holder mount
• Remove the cable from the car.
• Replace the cable with a new one and install the parts in the reverse order.
• Adjust the hand brake drive.

How to increase trunk volume

Many people noticed the huge size of the car, but at the same time small trunks. It is worth noting the fact that the Toyota Camry belongs to a business class car and the size of the trunk, one might say, is quite voluminous. However, this seems not enough to many car owners, and they think about how to increase the trunk volume.

First of all, you should try to unload the trunk. If there were previously any additional elements in the trunk, for example a net, then it needs to be removed. This will free up a lot of space.

If you need to transfer large cargo, the very first thing the driver can do is fold the back row of seats. It folds in a 60/40 ratio. The Toyota Camry also comes with a full-size spare tire. It can be replaced with a spare one from another car that will fit the Camry hub.

After the wheel is replaced, you should remove the plastic organizer of the full-size spare tire, since it eats up about 10 cm of space, and this is sometimes a very, very sensitive volume. Instead, you can install a mounting bolt. The cost of such a bolt will be approximately 300-400 Russian rubles.

You can increase the volume by purchasing new carpets for the trunk, which will fit more tightly and accurately, but this is not always a cheap option, so many people simply cut their old carpets so that they lie more evenly. You should also cut a piece of plywood so that the carpet does not sag too much.

There are also other options for increasing the trunk, but they are very risky. Some car owners suggest removing the spare tire and repair kit, but this kind of “tuning” is not recommended, since in the event of even a minor malfunction that requires a wheel replacement, you will have to call a tow truck, and this costs a lot of money.

Trunk volume Toyota RAV4 2021, 5th generation, XA50, SUV

Toyota RAV4 2018 review

Automatic trunk opening and trunk support replacement

Automatic trunk opening is another innovation that is in great demand among car enthusiasts. In some cases, automatic opening is installed at factories, but most cars do not have this option. In addition, the design installed at the factory for some reason may simply not suit the car owner. That's why car enthusiasts decide to make some updates.

When installing this system, it is better to change the pair at once. In this case, opening will be easier and when opening the trunk will not get stuck if it is heavy. You can do all this with your own hands. No additional parts are required, except for bolts or screws.

There is an option to open the trunk using the remote control. This is very convenient in winter; after washing, the lock may simply freeze. This will not happen with an electric drive. Connecting an electric drive is not the easiest process, so you should be prepared for it.

The electric drive consists of the following parts:

• Electric motor;
• Two four-pin relays;
• push rod;
• fuse;
• Buttons.

The kit also includes a diagram. There are two drive options. The first is a drive with a motor, and the second is a drive with magnetic plates. The first option is considered more practical and durable.

Before purchasing a mechanism, you should choose for yourself how the trunk will open. There are two options to choose from: using a button in the cabin or from the remote control. In the first case, you can do the entire installation yourself, but in the second, everything is much more complicated and such work should only be entrusted to a professional electrician.

Next you need to decide on the lock. There are two types of locks: standard, side-mounted and reinforced. The latter are a little more expensive, but also have better quality and reliability.

Preparing the car for tuning

When preparing the machine for modification, you should perform the following steps:

1. It is not recommended to drive the car into a closed garage equipped with a lift or inspection hole; it is not recommended to carry out repairs on the street.
2. Unscrew the screws securing the mudguard under the bumper.
3. Remove the mounting clips located in the front wheel arches.
4. Bend the fender liner away from the plastic shell, and then unscrew the bolts holding the corners of the decorative element to the body.
5. Remove the plastic clips and unscrew the bolts located under the hood of the car.
6. Move the side edges of the bumper to the sides, moving the latches out of the guide grooves in the brackets.
7. Gently pull the plastic shell towards you, unfastening the additional latches one by one.
8. Lay the structure on the floor of the garage, and then disconnect the plugs of the electrical wiring routed to the fog lights and parking assistant sensors (this option is not available on all cars).
9. If you plan to remove the headlights, you will need to unscrew the side bolts and 2 screws of the top mounting.
10. Pull the lighting device out of the mounting socket and disconnect the wiring harnesses one by one (for low and high beam lamps, side lights, direction indicators and electric installation angle corrector).
11. Clean the radiators of the cooling and air conditioning system from dirt. It is prohibited to use pressure washing, since the flow of water crushes the honeycombs, which leads to a deterioration in heat transfer.